the final sum may use up to 26 bits
+ add a unit test
+ disable the sse2 as the result will rollover; this will be fixed in a
future commit
Change-Id: I2a49811dfaa06abfd9fa1e1e65ed7cd68e4c97ce
tm_predictor_4x4 is implemented with SSE2 using XMM registers.
Speed up by ~25% in ./test_intra_pred_speed.
Change-Id: I25074b78d476a2cb17f81cf654bdfd80df2070e0
This change alters the nature and use of exhaustive motion search.
Firstly any exhaustive search is preceded by a normal step search.
The exhaustive search is only carried out if the distortion resulting
from the step search is above a threshold value.
Secondly the simple +/- 64 exhaustive search is replaced by a
multi stage mesh based search where each stage has a range
and step/interval size. Subsequent stages use the best position from
the previous stage as the center of the search but use a reduced range
and interval size.
For example:
stage 1: Range +/- 64 interval 4
stage 2: Range +/- 32 interval 2
stage 3: Range +/- 15 interval 1
This process, especially when it follows on from a normal step
search, has shown itself to be almost as effective as a full range
exhaustive search with step 1 but greatly lowers the computational
complexity such that it can be used in some cases for speeds 0-2.
This patch also removes a double exhaustive search for sub 8x8 blocks
which also contained a bug (the two searches used different distortion
metrics).
For best quality in my test animation sequence this patch has almost
no impact on quality but improves encode speed by more than 5X.
Restricted use in good quality speeds 0-2 yields significant quality gains
on the animation test of 0.2 - 0.5 db with only a small impact on encode
speed. On most clips though the quality gain and speed impact are small.
Change-Id: Id22967a840e996e1db273f6ac4ff03f4f52d49aa
This reverts commit 9aeaa2016e7470c4e316d90da33d883098eed6f4.
This causes some test vectors to fail.
Change-Id: I3659a2068404ec5a0591fba5c88b1bec0c9059a4
This reverts commit 380a5519cca999f54b17f37b709996a11f3204ea.
This causes an assertion failure in debug_check_frame_counts() which
probably isn't valid with this change; leaving the investigation for
later now.
Change-Id: Ieda5ca811ed2fa50a0cc6935919a8d10dca996e0
This function now has an AVX intrinsics version which is about 80%
faster compared to the C implementation. This provides a 2-4% total
speed-up for encode, depending on encoding parameters. The function
utilizes 3 properties of the cost function lookup table, constructed
in 'cal_nmvjointsadcost' and 'cal_nmvsadcosts'.
For the joint cost:
- mvjointsadcost[1] == mvjointsadcost[2] == mvjointsadcost[3]
For the component costs:
- For all i: mvsadcost[0][i] == mvsadcost[1][i]
(equal per component cost)
- For all i: mvsadcost[0][i] == mvsadcost[0][-i]
(Cost function is even)
These must hold, otherwise the AVX version of the function cannot be used.
Change-Id: I6c2791d43022822a9e6ab43cd124a773946d0bdc
the return value of enabled, which may be empty, is handled by the for
loop. this avoids making an unnecessarily long command line which may
fail in certain cases.
Change-Id: Ib88ecbbe2c0f6d7debb600b4caed4884497263b1
Change is only for real-time mode, speed >= 5, and non-screen content mode.
Add bias to zero/low motion for big blocks, if noise estimation
is enabled and noise level is above threshold.
Change-Id: I3a0a4608ede6aa535bda6eca528d20f8aba738e7
For 1 pass CBR mode: increase waiting time after key frame
before we start sampling rate control behavior for determining
resize. This change need to disable one internal resize(DownUp)
temporally since it requires a longer clip to do so.
Change-Id: If21beda1be23f169ee541ab4dd642f718347887a
Use same setting for speed 5 (as it is for speed > 5).
Change is only for real-time (non-rd) mode.
Change-Id: I830250eac654328373cb318baa89d4f0e63942e1
