webp/man/cwebp.1

.\"                                      Hey, EMACS: -*- nroff -*-
.TH CWEBP 1 "December 12, 2013"
.SH NAME
cwebp \- compress an image file to a WebP file
.SH SYNOPSIS
.B cwebp
.RI [ options ] " input_file \-o output_file.webp
.br
.SH DESCRIPTION
This manual page documents the
.B cwebp
command.
.PP
\fBcwebp\fP compresses an image using the WebP format.
Input format can be either PNG, JPEG, TIFF or raw Y'CbCr samples.
.SH OPTIONS
The basic options are:
.TP
.BI \-o " string
Specify the name of the output WebP file. If omitted, \fBcwebp\fP will
perform compression but only report statistics.
.TP
.B \-h, \-help
A short usage summary.
.TP
.B \-H, \-longhelp
A summary of all the possible options.
.TP
.B \-version
Print the version number (as major.minor.revision) and exit.
.TP
.BI \-q " float
Specify the compression factor for RGB channels between 0 and 100. The default
is 75.
.br
In case of lossy compression (default), a small factor produces a smaller file
with lower quality. Best quality is achieved by using a value of 100.
.br
In case of lossless compression (specified by the \-lossless option), a small
factor enables faster compression speed, but produces a larger file. Maximum
compression is achieved by using a value of 100.
.TP
.BI \-alpha_q " int
Specify the compression factor for alpha compression between 0 and 100.
Lossless compression of alpha is achieved using a value of 100, while the lower
values result in a lossy compression. The default is 100.
.TP
.BI \-f " int
Specify the strength of the deblocking filter, between 0 (no filtering)
and 100 (maximum filtering). A value of 0 will turn off any filtering.
Higher value will increase the strength of the filtering process applied
after decoding the picture. The higher the value the smoother the picture will
appear. Typical values are usually in the range of 20 to 50.
.TP
.BI \-preset " string
Specify a set of pre-defined parameters to suit a particular type of
source material. Possible values are:  \fBdefault\fP, \fBphoto\fP,
\fBpicture\fP, \fBdrawing\fP, \fBicon\fP, \fBtext\fP. Since
\fB\-preset\fP overwrites the other parameters' values (except the
\fB\-q\fP one), this option should preferably appear first in the
order of the arguments.
.TP
.BI \-sns " int
Specify the amplitude of the spatial noise shaping. Spatial noise shaping
(or \fBsns\fP for short) refers to a general collection of built-in algorithms
used to decide which area of the picture should use relatively less bits,
and where else to better transfer these bits. The possible range goes from
0 (algorithm is off) to 100 (the maximal effect). The default value is 80.
.TP
.BI \-m " int
Specify the compression method to use. This parameter controls the
trade off between encoding speed and the compressed file size and quality.
Possible values range from 0 to 6. Default value is 4.
When higher values are used, the encoder will spend more time inspecting
additional encoding possibilities and decide on the quality gain.
Lower value can result in faster processing time at the expense of
larger file size and lower compression quality.
.TP
.B \-jpeg_like
Change the internal parameter mapping to better match the expected size
of JPEG compression. This flag will generally produce an output file of
similar size to its JPEG equivalent (for the same \fB\-q\fP setting), but
with less visual distortion.
.TP
.B \-mt
Use multi-threading for encoding, if possible. This option is only effective
when using lossy compression on a source with a transparency channel.
.TP
.B \-low_memory
Reduce memory usage of lossy encoding by saving four times the compressed
size (typically). This will make the encoding slower and the output slightly
different in size and distortion. This flag is only effective for methods
3 and up, and is off by default. Note that leaving this flag off will have
some side effects on the bitstream: it forces certain bitstream features
like number of partitions (forced to 1). Note that a more detailed report
of bitstream size is printed by \fBcwebp\fP when using this option.
.TP
.B \-af
Turns auto-filter on. This algorithm will spend additional time optimizing
the filtering strength to reach a well-balanced quality.

.SH ADDITIONAL OPTIONS
More advanced options are:
.TP
.BI \-sharpness " int
Specify the sharpness of the filtering (if used).
Range is 0 (sharpest) to 7 (least sharp). Default is 0.
.TP
.B \-strong
Use strong filtering (if filtering is being used thanks to the
\fB\-f\fP option). Strong filtering is on by default.
.TP
.B \-nostrong
Disable strong filtering (if filtering is being used thanks to the
\fB\-f\fP option) and use simple filtering instead.
.TP
.BI \-segments " int
Change the number of partitions to use during the segmentation of the
sns algorithm. Segments should be in range 1 to 4. Default value is 4.
This option has no effect for methods 3 and up, unless \fB\-low_memory\fP
is used.
.TP
.BI \-partition_limit " int
Degrade quality by limiting the number of bits used by some macroblocks.
Range is 0 (no degradation, the default) to 100 (full degradation).
Useful values are usually around 30-70 for moderately large images.
In the VP8 format, the so-called control partition has a limit of 512k and
is used to store the following information: whether the macroblock is skipped,
which segment it belongs to, whether it is coded as intra 4x4 or intra 16x16
mode, and finally the prediction modes to use for each of the sub-blocks.
For a very large image, 512k only leaves room to few bits per 16x16 macroblock.
The absolute minimum is 4 bits per macroblock. Skip, segment, and mode
information can use up almost all these 4 bits (although the case is unlikely),
which is problematic for very large images. The partition_limit factor controls
how frequently the most bit-costly mode (intra 4x4) will be used. This is
useful in case the 512k limit is reached and the following message is displayed:
\fIError code: 6 (PARTITION0_OVERFLOW: Partition #0 is too big to fit 512k)\fP.
If using \fB-partition_limit\fP is not enough to meet the 512k constraint, one
should use less segments in order to save more header bits per macroblock.
See the \fB-segments\fP option.
.TP
.BI \-size " int
Specify a target size (in bytes) to try and reach for the compressed output.
Compressor will make several pass of partial encoding in order to get as
close as possible to this target.
.TP
.BI \-psnr " float
Specify a target PSNR (in dB) to try and reach for the compressed output.
Compressor will make several pass of partial encoding in order to get as
close as possible to this target.
.TP
.BI \-pass " int
Set a maximum number of passes to use during the dichotomy used by
options \fB\-size\fP or \fB\-psnr\fP. Maximum value is 10.
.TP
.BI \-resize " width height
Resize the source to a rectangle with size \fBwidth\fP x \fBheight\fP.
If either (but not both) of the \fBwidth\fP or \fBheight\fP parameters is 0,
the value will be calculated preserving the aspect-ratio.
.TP
.BI \-crop " x_position y_position width height
Crop the source to a rectangle with top-left corner at coordinates
(\fBx_position\fP, \fBy_position\fP) and size \fBwidth\fP x \fBheight\fP.
This cropping area must be fully contained within the source rectangle.
.TP
.BI \-s " width height
Specify that the input file actually consists of raw Y'CbCr samples following
the ITU-R BT.601 recommendation, in 4:2:0 linear format.
The luma plane has size \fBwidth\fP x \fBheight\fP.
.TP
.BI \-map " int
Output additional ASCII-map of encoding information. Possible map values
range from 1 to 6. This is only meant to help debugging.
.TP
.BI \-pre " int
Specify some pre-processing steps. Using a value of '2' will trigger
quality-dependent pseudo-random dithering during RGBA->YUVA conversion
(lossy compression only).
.TP
.BI \-alpha_filter " string
Specify the predictive filtering method for the alpha plane. One of 'none',
\&'fast' or 'best', in increasing complexity and slowness order. Default is
\&'fast'. Internally, alpha filtering is performed using four possible
predictions (none, horizontal, vertical, gradient). The 'best' mode will try
each mode in turn and pick the one which gives the smaller size. The 'fast'
mode will just try to form an a-priori guess without testing all modes.
.TP
.BI \-alpha_method " int
Specify the algorithm used for alpha compression: 0 or 1. Algorithm 0 denotes
no compression, 1 uses WebP lossless format for compression. The default is 1.
.TP
.B \-alpha_cleanup
Modify unseen RGB values under fully transparent area, to help compressibility.
The default is off.
.TP
.BI \-blend_alpha " int
This option blends the alpha channel (if present) with the source using the
background color specified in hexadecimal as 0xrrggbb. The alpha channel is
afterward reset to the opaque value 255.
.TP
.B \-noalpha
Using this option will discard the alpha channel.
.TP
.B \-lossless
Encode the image without any loss.
.TP
.BI \-hint " string
Specify the hint about input image type. Possible values are:
\fBphoto\fP, \fBpicture\fP or \fBgraph\fP.
.TP
.BI \-metadata " string
A comma separated list of metadata to copy from the input to the output if
present.
Valid values: \fBall\fP, \fBnone\fP, \fBexif\fP, \fBicc\fP, \fBxmp\fP.
The default is \fBnone\fP.

Note: each input format may not support all combinations.
.TP
.B \-noasm
Disable all assembly optimizations.
.TP
.B \-v
Print extra information (encoding time in particular).
.TP
.B \-print_psnr
Compute and report average PSNR (Peak-Signal-To-Noise ratio).
.TP
.B \-print_ssim
Compute and report average SSIM (structural similarity
metric, see http://en.wikipedia.org/wiki/SSIM for additional details).
.TP
.B \-print_lsim
Compute and report local similarity metric (sum of lowest error amongst the
collocated pixel neighbors).
.TP
.B \-progress
Report encoding progress in percent.
.TP
.B \-quiet
Do not print anything.
.TP
.B \-short
Only print brief information (output file size and PSNR) for testing purpose.

.SH BUGS
Please report all bugs to our issue tracker:
http://code.google.com/p/webp/issues
.br
Patches welcome! See this page to get started:
http://www.webmproject.org/code/contribute/submitting-patches/

.SH EXAMPLES
cwebp \-q 50 -lossless picture.png \-o picture_lossless.webp
.br
cwebp \-q 70 picture_with_alpha.png \-o picture_with_alpha.webp
.br
cwebp \-sns 70 \-f 50 \-size 60000 picture.png \-o picture.webp
.br
cwebp \-o picture.webp \-\- \-\-\-picture.png

.SH AUTHORS
\fBcwebp\fP was written by the WebP team.
.br
The latest source tree is available at http://www.webmproject.org/code
.PP
This manual page was written by Pascal Massimino <pascal.massimino@gmail.com>,
for the Debian project (and may be used by others).

.SH SEE ALSO
.BR dwebp (1),
.BR gif2webp (1).
.br
Please refer to http://developers.google.com/speed/webp/ for additional
information.