The warning only happens in VP9 encoder's first pass due to src_mi
is not set up yet. But it will not fail the encoder as left_mi and
above_mi are not used in the first_pass and they will be set up again
in the second pass.
Change-Id: I12dffcd5fb1002b2b2dabb083c8726650e4b5f08
This allows us to track decode speed for new encodes so that we catch
problems like an encode change that makes decode really slow.
Change-Id: I92251a8b1f710b241f66e1042413df1b71b76038
This commit enables the use of sub8x8 blocks in RTC key frame
encoding. It requires the block size to be preset and will decide
the coding mode and encode the bit-stream.
Change-Id: I35aaf8ee2d4d6085432410c7963f339f85a2c19b
Rename set_modeinfo_offsets as set_mode_info_offsets, to be more
consistent with naming convention.
Change-Id: I68ca1f36c4a78127d9439a50c1506a2afd07927d
The later encoding process will take the top-left block's
mode_info for pre-determined block size.
Change-Id: I76a90f9ce7f3b2dbc2975b52442114e461c465b5
The function vp9_filter_block1d16_h8_ssse3 uses the PSHUFB instruction which has a 3 cycle latency and slows execution when done in blocks of 5 or more on Atom processors.
By replacing the PSHUFB instructions with other more efficient single cycle instructions (PUNPCKLBW + PUNPCHBW + PALIGNR) performance can be improved.
In the original code, the PSHUBF uses every byte and is consecutively copied.
This is done more efficiently by PUNPCKLBW and PUNPCHBW, using PALIGNR to concatenate the intermediate result and then shift right the next consecutive 16 bytes for the final result.
For example:
filter = 0,1,1,2,2,3,3,4,4,5,5,6,6,7,7,8
Reg = 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
REG1 = PUNPCKLBW Reg, Reg = 0,0,1,1,2,2,3,3,4,4,5,5,6,6,7,7
REG2 = PUNPCHBW Reg, Reg = 8,8,9,9,10,10,11,11,12,12,13,13,14,14,15,15
PALIGNR REG2, REG1, 1 = 0,1,1,2,2,3,3,4,4,5,5,6,6,7,7,8
This optimization improved the function performance by 23% and produced a 3% user level gain on 1080p content on Atom processors.
There was no observed performance impact on Core processors (expected).
Change-Id: I3cec701158993d95ed23ff04516942b5a4a461c0
Adds decoder config as a changeable parameter to unit tests, and
changes end to end test to use commonly used parameters to enable
base test of tiles encoding and frame parallel decoding.
Change-Id: I5d23a6857303b4d68b92b15c3f2f04a1bcb4c2bb
the flag in the header wasn't being set based on the encoder
configuration in non-intra only mode
broken since:
fbc2fbf Adding oxcf temp variable.
Change-Id: Ib4cff9901889824bc4e68d7f0f6deb1e41df2f53
The initial reset of this_rdc in vp9_pick_inter_mode is not needed,
since it will be re-assign when used.
Change-Id: Ic0e12d741cbab292fc214c1eabb48b129af7839b
Compare the current best mode rate-distortion cost with the skip
threshold to decide if performing motion search.
Change-Id: Ia071824f8dd3b7db485f424692a485a2da6a1a9f
These speed-up features for key frame coding are only turned on
in the settings of hybrid non-RD and RD mode decision. It provides
about 20% speed-up to the hybrid key frame coding at the expense
of certain compression performance loss. For vidyo1, the key frame
coding statistics are changed
9838F, 35.020 dB, 61677 us -> 9920F, 34.834 dB, 47556 us
Overall rtc set compression performance is down by -0.257%.
Change-Id: I0025447fda26bb7855e982955642b5f55d71b51f
