The idea is to have the following names for each transform size:
vp9_idct4x4_add
vp9_idct4x4_1_add
vp9_idct4x4_10_add
vp9_idct4x4_16_add
vp9_idct8x8_add
vp9_idct8x8_1_add
vp9_idct8x8_10_add
vp9_idct8x8_64_add
etc for 16x16, 32x32
The actual list of renames in this patch:
vp9_idct_add_lossless -> vp9_iwht4x4_add
vp9_short_iwalsh4x4_add -> vp9_iwht4x4_16_add
vp9_short_iwalsh4x4_1_add -> vp9_iwht4x4_1_add
vp9_idct_add -> vp9_idct4x4_add
vp9_short_idct4x4_add -> vp9_idct4x4_16_add
vp9_short_idct4x4_1_add -> vp9_idct4x4_1_add
Change-Id: I6f43f7437c68dd30cdd05d72e213765578ed30b1
Speed 4 still does not give a big gain over speed 3.
This just cleans it up a little from the last patch and comments
out features that do not seem to be giving much benefit.
Change-Id: I5f366e6160e1dbe5dc45cf5eb90cc02712baa1b6
Allow selective masking of individual split modes rather than
just a single on / off flag.
For speed 2 recovers the large speed loss seen for some derf
clips in change Ie6bdfa0a370148dd60bd800961077f7e97e67dd4
and a small quality gain.
For speed 1 10 % speed increase observed locally on some derf clips
for minimal quality change.
Change-Id: If86191087b93cbc05351c26c60c7933e2149e485
This commit removes the redundant second reference frame check in
the rate-distortion optimization loop for sub8x8 blocks.
Change-Id: I13a57a6f624c4a9bcef02ff2a867fa30d8b44a93
This commit defines b_mode_info as a struct type. This will allow
us to further remove the use of PARTITION_INFO in the encoding process.
Change-Id: I975b0f7d557b5e0f66545a61b472def76b671cce
This commit separates the rate-distortion optimization loop of
superblocks from that of sub8x8 blocks. This allows better design
rate-distortion optimization search loop for each setting. It also
removes the use of SPLITMV and I4X4_PRED therein.
No performance change in speed 0 settings. For bus@CIF at 2000kbps,
the speed 1 runtime goes from 48009ms to 43894ms (about 10% faster).
The overall compression performance on derf changed by -0.021%.
Speed 2 runtime goes from 27114ms to 28700ms (6% slower), while the
overall coding efficiency goes up by 1.629% for derf, 1.236% for yt.
Change-Id: Ie6bdfa0a370148dd60bd800961077f7e97e67dd4
Substantial reworking of the speed vs quality trade offs for
speed 1 and 2.
In this patch I am attempting to freeze the "quality" meaning of
speeds 1 and 2 relative to speed 0 so that in future we can
better evaluate progress.
I am targeting :
Speed 1 quality ~-5% vs speed 0.
Speed 2 quality ~-10% vs speed 0
It is inevitable that quality will still fluctuate a little as we adjust
settings and add new features, but we will attempt to keep as
close as possible to these values. Above speed 2 things will remain
a bit more fluid for now.
In this patch speed 1 is approximately 4-5x as fast as speed 0. This
is similar to before but the quality hit is a lot less. Likewise speed 2
is approximately 2x as fast as speed 1 but is similar in quality to the
previous speed 1 configuration.
Also slight change to behavior of FLAG_EARLY_TERMINATE to insure
all reference frames get at least one rd test. Important for very low
variance regions.
WIP :- Added a new speed level with old speed 4 becoming speed 5.
Speed 3 and 4 tradeoffs still WIP
Change-Id: Ic7a38dd7b5b63ab1501f9352411972f480ac6264
This commit causes use last partition to consider whether a 64x64 has
motion that might make a new partitioning worth while.
Change-Id: I3a57bedef4f3cd961fadbfa96651c206fa36da4a
Simplify the k_cvtlo_epi16 and k_cvthi_epi16 to only two
instructions. Then inlined them.
quoting from intel MMX_App_Compute_16bit_Vector.pdf
"The PMADDWD instruction multiplies four
pairs of 16-bit numbers and produces partial sums of the results
and can do so once per clock (with a three-clock latency)."
so I am assuming that there will be three clock overhead after the
last _mm_madd_pi16 command.
Even with the overhead the number of clocks in general should be
smaller. I am not sure though becasue I could not find information
about number of clocks required for instructions in k_cvtlo_epi16
and k_cvthi_epi16. I will run a test and compare the execution time.
Change-Id: Ieda4aa338f69ad3dd196ac6e7892da3cf1b47ea7
Moving functions from vp9_idct_blk to vp9_idct because these functions are
used from both encoder and decoder. Removing duplicated code from
vp9_encodemb.c and reusing existing functions.
Change-Id: Ia0a6782f8c4c409efb891651b871dd4bf22d5fe8
Make encoder skip rectangular partition check in speed 1 and above,
when early termination was triggered in partition split.
Thanks Guillaume (gmartres@) for catching this issue.
This change makes bus_cif at 2000kbps speed 1 runtime goes down from
25612ms to 23438ms (about 9% speed-up), at the expense of -0.235%
performance down.
Change-Id: I98613fad081a261d30d5fa206f934ca70601c180
