For VBR: (1) allow newmv mode for golden ref to
select interpolation filter (as in last ref case), and
(2) don't use the more aggressive tx-skip testing logic for large blocks.
Only affects 1 pass real-time vbr mode (speed >= 5).
PSNR/SSIM metrics on ytlive set are all positive, ~0.5-2% gain.
Change-Id: I0ffbb0a9755563a5acd6230c58236e4f19a47266
This change is only for real-time mode if short_circuit_low_temp_var
is on. Add bias to last frame in choosing ref frame for partitioning,
when y_sad and y_sad_g are close. It speeds up real-time encoding by
0.5% on some clips with less than 0.1% overall PSNR drop on rtc test set.
Change-Id: I2a2110fe36455f3d8f0fc404aef2228f512e8df8
1. Skip golden non-zeromv and newmv-last for bsize >= 16x16 if the
temporal variance obtained from choose_partitioning is very low.
2. Skip horz and vert INTRA mode for speed 8.
This change works best on the clips with little noise and with some
motion (e.g. gips_motion which has > 5% speed up). PSNR drop is 1.78%
on rtc test set, no obvious visual quality regression found.
Change-Id: Ib43b5b20e67809d03c5a6890818ddff59e1fc94a
Move initialization of a some new "twopass" values
to the function vp9_init_second_pass() and some other
small changes.
Remove #if GROUP_ADAPTIVE_MAXQ as this is always
enabled now.
Change-Id: I1dbec2fd7c419779848aa987c4cd7824d4df8456
On scene-cut detected frames (i.e., high_source_sad = 1), use
nonrd_pick_partition (over choose_part + select_part), as
the nonrd_pick partitioning is generally better.
Small positive increase in metrics on ytlive set (~0.5 - 1%).
Negligle overall speed decrease, as its only used on scene-cut frames.
Only affects 1 pass vbr mode, speed = 5.
Change-Id: I07c89cbdc75f5bb16eb8e0e2773ead0980d2de5c
This reverts commit be12fefa4b7d224e9f39275a6bb4fab01b8bae3b
and commit 057c1c4034ba5b9bf360c5c1f600ebc6d0718c3a.
Also, the mismatch between the avx version and the
c version has been fixed.
BUG=https://bugs.chromium.org/p/webm/issues/detail?id=1168
For a rt encode using 1080p@60fps material, up to 11% performance
improvement overall was seen.
Change-Id: Icd1f216209ebc6fc0b8da885f32f356fa4355ed0
The eob of a block is not perperly set when skip_recode is true,
thus triggering assert(eob <= default_eob) to fail.
Change-Id: Ifecbe33dce2dc4903e0a80bd384dc09bf0dd8a44
Code cleaup, use existing rolling_actual/target metrics instead,
set threshold to get same/similar effect.
Little/no change in metrics on ytlive set.
Change-Id: I74f3c3d0a143a9cf20dc9c3dee54c0f7e6a97a51
Add a max condition and lower the min value.
No change in behavior (metrics for yt live set) for the
default min/max_gf_interval=4/16 settings.
Small positive change when min/max_gf_interval=7/16
(for 60fps clips on ytlive set).
Change-Id: I1c1d72425c86c69419ea43fb9730130e81062f91
Error messages:
..\vp9\common\vp9_loopfilter.c(1312): warning C4244: 'function' :
conversion from 'uint64_t' to 'unsigned int', possible loss of data
[.build-x86_64-win64-vs10\vpx.vcxproj]
..\vp9\common\vp9_loopfilter.c(1313): warning C4244: 'function' :
conversion from 'uint64_t' to 'unsigned int', possible loss of data
[.build-x86_64-win64-vs10\vpx.vcxproj]
..\vp9\common\vp9_loopfilter.c(1312): error C2220: warning treated as
error - no 'object' file generated
[.build-x86_64-win64-vs10\vpx.vcxproj]
Change-Id: Ia69260611997cd2ba41c7184a85ecead740a7c07
Increase in the damping used in adjusting the active Q range.
This does hurt rate accuracy a little in a few extreme cases
especially if the clip is very short*, but helps metrics.
* Note that the adjustment is applied at the GF/ARF group level based
on what happened in the last group. Hence for very short clips where
the length of a single group may be a significant % of the clip length
there is still scope for some drift that cannot be accommodated.
In practice most data points in our test sets are now much closer to target
than was previously the case with default settings and in some cases are
better even than they were with the command line undershoot and overshoot
parameter was set very low (e.g. 2%). For example in bridge_close at high rates
the old mechanism was unable to adapt enough to prevent extreme overshoot.
Change-Id: I634f8f0e015b5ee64a9f0ccaa2bcfdbc1d360489
Change to the calculation of the error divisor used in
get_twopass_worst_quality(). This follows on from other
changes to the rate control that impact the output of this
function.
Change-Id: I414fa9aa1e6a68a64dccea17c3712f44b8a0c10c
Changes to the function the redistributes bits from overshoot
or undershoot throughout the rest of the clip to respond more
quickly.
Change-Id: I90f10900cdd82cf2ce1d8da4b6f91eb5934310da
Added a factor based on the bit spend in the last arf group vs the
target to adjust the choice of the active worst quality in subsequent
groups.
Helps clips where previously there was a big overshoot or undershoot
to adapt and get closer to the target rate.
Change-Id: I67034b801679b99024409489a2273ea6fe23b8e6
The use of this value is preventing rate adjustment on clips
or sections that have very little motion but high noise and
this can give rise to some sections with massive overshoot.
Change-Id: I9a65c7c1148dc5d3a7d8b23e50fc1733f3661621
