Commit 0ce3901 introduced a change in the frame buffer copy logic where
the NEW frame could be copied to the ARF or GF buffer through the
copy_buffer_to_{arf,gf}==1 flags, if the LAST frame was not being
refreshed. This is not correct. The intent of the
copy_buffer_to_{arf,gf}==1 flag is to copy the LAST buffer. To copy the
NEW buffer, the refresh_{alt_ref,golden}_frame flag should be used.
The original buffer copy logic is fairly convoluted. For example:
if (cm->refresh_last_frame)
{
vp8_swap_yv12_buffer(&cm->last_frame, &cm->new_frame);
cm->frame_to_show = &cm->last_frame;
}
else
{
cm->frame_to_show = &cm->new_frame;
}
...
if (cm->copy_buffer_to_arf)
{
if (cm->copy_buffer_to_arf == 1)
{
if (cm->refresh_last_frame)
vp8_yv12_copy_frame_ptr(&cm->new_frame, &cm->alt_ref_frame);
else
vp8_yv12_copy_frame_ptr(&cm->last_frame, &cm->alt_ref_frame);
}
else if (cm->copy_buffer_to_arf == 2)
vp8_yv12_copy_frame_ptr(&cm->golden_frame, &cm->alt_ref_frame);
}
Effectively, if refresh_last_frame, then new and last are swapped, so
when "new" is copied to ARF, it's equivalent to copying LAST to ARF. If
not refresh_last_frame, then LAST is copied to ARF. So LAST is copied to
ARF in both cases.
Commit 0ce3901 removed the first buffer swap but kept the
refresh_last_frame?new:last behavior, changing the sense since the first
swap wasn't done to the more readable refresh_last_frame?last:new, but
this logic is not correct when !refresh_last_frame.
This commit restores the correct behavior from v0.9.1 and prior. This
case is missing from the test vector set.
Change-Id: I8369fc13a37ae882e31a8a104da808a08bc8428f
The following features don't make sense for the first
pass in its current form and have a significant impact on its
speed (up to 50%).
Slow quantizer, slow dct and trellis optimization.
Change-Id: Id9943f6765ffbd71fc0084ec7dfbc9d376fd6fcd
Calculate a minimum intra value to be used in determining the
IIratio scores used in two pass, second pass.
This is to make sure sections that are low complexity" in the
intra domain are still boosted appropriately for KF/GF/ARF.
For now I have commented out the Q based adjustment of
KF boost.
Change-Id: I15deb09c5bd9b53180a2ddd3e5f575b2aba244b3
Scott pointed out that last_frame_type only gets updated while
loopfilter exists. Since last_frame_type is also needed in
motion search now, it needs to be updated every frame.
Change-Id: I9203532fd67361588d4024628d9ddb8e391ad912
Use the fast quantizer for inter mode selection and the
regular quantizer for the rest of the encode for good quality,
speed 1. Both performance and quality were improved. The
quality gains will make up for the quality loss mentioned in
I9dc089007ca08129fb6c11fe7692777ebb8647b0.
Change-Id: Ia90bc9cf326a7c65d60d31fa32f6465ab6984d21
1. Search for block8x16/block16x8 uses block8x8's search results.
2. Check block4x4 only if block8x8 is chosen. (This hurts quality,
which will be improved in another check-in.)
3. In block4x4 search, the previous block's result is used as
MV predictor for next block.
This change improves performance.
Change-Id: I9dc089007ca08129fb6c11fe7692777ebb8647b0
Re-calibrated sad_per_bit16 and sad_per_bit4 tables to linearly
correlated to quantizer values, these two variables are used in
motion search for costing motion vectors. This change has an small
positive effect on compression.
Change-Id: Ic9b5ea6fb8d5078ef663ba4899db019cc51f4166
stats_close() was not freeing memory for
single pass runs. It now takes in arg_passes
to determine when it should free memory.
Change-Id: I6623b7e30b76f9bf2e16008490f9b20484d03f31
the lookup table is based on floating point calculations (see source)
by moving the *3 before the downshift and adding the rounding bit, the
delta (LUT - integer) goes from:
______________________________________
__ 1__ 1______________________________
__ 1__ 1______________________________
____ 1______ 1________________________
____ 1 2__ 2 1________________________
______ 1 1 2__ 2__ 2__ 2 1 1__________
________ 1 1 2 2__ 1 2 3 1 2__ 2__ 2__
to:
__-1__-1______________________________
______________________________________
____-1______-1________________________
______________________________________
________-1______________-1____________
______________________________________
it's important to be able to use the integer version because the LUT
more or less precludes SIMD optimizations
Change-Id: I45a81127dc7b72a06fba951649135d9d918386c0
allow for optimized versions of apply_temporal_filter
(now vp8_apply_temporal_filter_c)
the function was previously declared as static and appears to have been
inlined. with this change, that's no longer possible. performance takes
a small hit.
the declaration for vp8_cx_temp_filter_c was moved to onyx_if.c because
of a circular dependency. for rtcd, temporal_filter.h holds the
definition for the rtcd table, so it needs to be included by onyx_int.h.
however, onyx_int.h holds the definition for VP8_COMP which is needed
for the function prototype. blah.
Change-Id: I499c055fdc652ac4659c21c5a55fe10ceb7e95e3
The pointer passed in the user_priv argument to vpx_codec_decode()
should be propagated through to the corresponding output frame and
made available in the image's user_priv member. Fixes issue #252
Change-Id: I182746a6882c8549fb146b4a4fdb64f1789eb750
Add a new encoder control, VP8E_SET_TUNING, to allow the application
to inform the encoder that the material will benefit from certain
tuning. Expose this control as the --tune option to vpxenc. The args
helper is expanded to support enumerated arguments by name or value.
Two tunings are provided by this patch, PSNR (default) and SSIM.
Activity masking is made dependent on setting --tune=ssim, as the
current implementation hurts speed (10%) and PSNR (2.7% avg,
10% peak) too much for it to be a default yet.
Change-Id: I110d969381c4805347ff5a0ffaf1a14ca1965257
