68 lines
2.9 KiB
Plaintext
68 lines
2.9 KiB
Plaintext
@TEMPLATE decoder_tmpl.c
|
|
Postprocessing Decoder
|
|
======================
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ INTRODUCTION
|
|
This example adds postprocessing to the simple decoder loop.
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ INTRODUCTION
|
|
|
|
|
|
Initializing Postprocessing
|
|
---------------------------
|
|
You must inform the codec that you might request postprocessing at
|
|
initialization time. This is done by passing the VPX_CODEC_USE_POSTPROC
|
|
flag to `vpx_codec_dec_init`. If the codec does not support
|
|
postprocessing, this call will return VPX_CODEC_INCAPABLE. For
|
|
demonstration purposes, we also fall back to default initialization if
|
|
the codec does not provide support.
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ DEC_INIT
|
|
/* Initialize codec */
|
|
res = vpx_codec_dec_init(&codec, interface, NULL,
|
|
VPX_CODEC_USE_POSTPROC);
|
|
if(res == VPX_CODEC_INCAPABLE) {
|
|
printf("NOTICE: Postproc not supported by %s\n",
|
|
vpx_codec_iface_name(interface));
|
|
res = vpx_codec_dec_init(&codec, interface, NULL, 0);
|
|
}
|
|
if(res)
|
|
die_codec(&codec, "Failed to initialize decoder");
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ DEC_INIT
|
|
|
|
|
|
Using Adaptive Postprocessing
|
|
-----------------------------
|
|
VP6 provides "adaptive postprocessing." It will automatically select the
|
|
best postprocessing filter on a frame by frame basis based on the amount
|
|
of time remaining before the user's specified deadline expires. The
|
|
special value 0 indicates that the codec should take as long as
|
|
necessary to provide the best quality frame. This example gives the
|
|
codec 15ms (15000us) to return a frame. Remember that this is a soft
|
|
deadline, and the codec may exceed it doing its regular processing. In
|
|
these cases, no additional postprocessing will be done.
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ DECODE
|
|
/* Decode the frame with 15ms deadline */
|
|
if(vpx_codec_decode(&codec, frame, frame_sz, NULL, 15000))
|
|
die_codec(&codec, "Failed to decode frame");
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ DECODE
|
|
|
|
|
|
Codec Specific Postprocessing Controls
|
|
--------------------------------------
|
|
Some codecs provide fine grained controls over their built-in
|
|
postprocessors. VP8 is one example. The following sample code toggles
|
|
postprocessing on and off every 15 frames.
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ PRE_DECODE
|
|
#if CONFIG_VP8_DECODER
|
|
if(frame_cnt%30 == 1) {
|
|
vp8_postproc_cfg_t pp = {0, 0, 0};
|
|
|
|
if(vpx_codec_control(&codec, VP8_SET_POSTPROC, &pp))
|
|
die_codec(&codec, "Failed to turn off postproc");
|
|
} else if(frame_cnt%30 == 16) {
|
|
vp8_postproc_cfg_t pp = {VP8_DEBLOCK | VP8_DEMACROBLOCK, 4, 0};
|
|
|
|
if(vpx_codec_control(&codec, VP8_SET_POSTPROC, &pp))
|
|
die_codec(&codec, "Failed to turn on postproc");
|
|
};
|
|
#endif
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ PRE_DECODE
|