When the keyframe distance is fixed the first interval has the right
distance but, the next ones have kf_distance + 1.
Change-Id: I44f1190fe7146124bd07660a5e0ef08829e3ae07
common/arm/vpx_asm_offsets moves up a level. prepare for muxing with
encoder/arm/vpx_vp8_enc_asm_offsets
Change-Id: I89a04a5235447e66571995c9d9b4b6edcb038e24
The encoder was not correctly catching transitions in the quantizer
deltas. If a delta_q was set, then the quantizer would be reinitialized
on every frame, but if they transitioned to 0, the quantizer would
not be reinitialized, leading to a encode-decode mismatch.
This bug was triggered by commit 999e155, which sets a Y2 delta Q
for very low base Q levels.
Change-Id: Ia6733464a55ee4ff2edbb82c0873980d345446f5
Whe auto keyframe insertion is enabled and conditions are right (scene change)
the encoder can decide to insert a key frame and does a re-encoding. This can
introduce extra latency. In RT mode we do not do the re-encoding of the current
frame but force the next frame to key frame.
Change-Id: I15c175fa845ac4c1a1f18bea3676e154669522a7
Reduce the number of sync points by letting each thread
continue imediatly with a new MB row.
Better multicore scaling, improves performance by 5-20% on ARM multicore.
Change-Id: Ic97e4d1c4886a842c85dd3539a93cb217188ed1b
from vp8cx_encode_intra_macro_block. prediction_error is used when
deciding if a frame should be a keyframe. After reviewing this with
Yaowu, it was pointed out that vp8cx_encode_intra_macro_block
is only called for keyframes, so the accumulation is unnecessary.
Change-Id: Id79dc81b80d4f5d124f3a0dba1b923887e2e1ec8
vp8_pick_intra4x4mby_modes uses the passed in distortion
for an early breakout. The best distortion was never saved
and the distortion for TM_PRED was always used.
Change-Id: Idbaf73027408a4bba26601713725191a5d7b325e
Previously, the DC check is to make sure there is no code-able
DC shift for quantizer Q0, which has been verified rather
conservative. This commit changes the criteria to have two
components, DC and AC, to address the conservativeness. First,
it checks if all AC energy is enough to contribute a single
non-zero quantized AC coefficient. Second, for DC, the decision
to skip further considers two possible scenarios: 1. There is
no code-able 2nd order DC coefficient at all; 2 The residue is
relatively flat, but the uniform DC change is very small, i.e.
less than 1/2 gray level per pixel.
Comparing to previous criteria, the new criteria is about 10%
to 15% faster in encoding time with a very small quality loss.
(threshold ~1000 and quality range 33db-45db)
It should be noted that this commit enables "automatic" static
threshold for encodebreakout if a non-zero small value is passed
in to encoder.
Change-Id: I0f77719a1ac2c2dfddbd950d84920df374515ce3
The condition for using RD when selecting the intra coding mode
for a MB is that the RD flag is set AND we're not in real-time
mode.
Previously the code used RD if either the RD flag was set OR
we were not using real-time mode.
Change-Id: Ic711151298468a3f99babad39ba8375f66d55a08
This function was using a variance metric compared to and SSE metric in
other places (eg. vp8_rd_inter_uv)
Change-Id: I9109fcc5a13bca9db1d7ead500fe14999ab233eb
Adds following targets to configure script to support RVCT compilation
without operating system support (for Profiler or bare metal images).
- armv5te-none-rvct
- armv6-none-rvct
- armv7-none-rvct
To strip OS specific parts from the code "os_support"-config was added
to script and CONFIG_OS_SUPPORT flag is used in the code to exclude OS
specific parts such as OS specific includes and function calls for
timers and threads etc. This was done to enable RVCT compilation for
profiling purposes or running the image on bare metal target with
Lauterbach.
Removed separate AREA directives for READONLY data in armv6 and neon
assembly files to fix the RVCT compilation. Otherwise
"ldr <reg>, =label" syntax would have been needed to prevent linker
errors. This syntax is not supported by older gnu assemblers.
Change-Id: I14f4c68529e8c27397502fbc3010a54e505ddb43
vp8/encoder/rdopt.c:728: warning: pointer targets in passing argument 3
of 'macro_block_yrd' differ in signedness
vp8/encoder/rdopt.c:541: note: expected 'int *' but argument is of type
'unsigned int *'
distortion is signed when calling macro_block_yrd is both other cases,
as well as for RDCOST
Change-Id: I5e22358b7da76a116f498793253aac8099cb3461
Change-Id: I6ca2d89f355839c4c770773c09fc69dcea7c1406
warning: implicit declaration of function
'vp8_variance_halfpixvar16x16_[h|v|hv]_neon'
'vp8_sub_pixel_variance16x16_neon_func'
Improved the performance of the first pass only
(~6% on 720p test clip) by making use of LUT instead of the
float calculations. Might try a SIMD version later.
Also started to make use of int_mv instead of
MV.
Change-Id: If2a217c7d6b59cd2c25c5553e0ca7e0502403af8
Use the function macro_block_yrd() to calculate error and distortion
in keeping with what is done for inter frames.
The old code was using a variance metric for once case and an
SSE function for measuring distortion in the other case.
The function vp8_encode_intra16x16mbyrd() is no longer used.
Change-Id: Ic228cb00a78ff637f4365b43f58fbe5a9273d36f
The code previously tested cpi->common.refresh_alt_ref_frame
but there are situations where this flag may be set for viewable frames.
The correct test should be !cm->show_frame.
Change-Id: Ia1a600622992a4a68fe1d38ac23bf6b34b133688
This commit also removes artificial RDMULT cap for low quantizers.
The intention is to address some abnormal behavior of mode selections
at the low quantizer end, where many macroblocks were coded with
SPLITMV with all partitions using same motion vector including (0,0).
This change improves the compression quality substantially for high
quality encodings in both PSNR and SSIM terms. Overall effect on
mid/low rate range is also positive for all metrics, but smaller
in magnitude.
Change-Id: I864b29c4bd9ff610d2545fa94a19cc7e80c02667
Commit 336aa0b7da incorrectly
declared current_pos as and int, when it should have been
a FIRSTPASS_STATS pointer.
Change-Id: I0a51c7a86ebba8546c95dd5d9d1c1143d4613e40
Adjust checking points in motion vector prediction to better cover
possible movements, and get a better prediction. Tests on test
clips showed a 0.1% improvement in SSIM, and no change in PSNR
and performance.
Change-Id: Ifdab05d35e10faea1445c61bb73debf888c9d2f8
The old 2 pass code estimated error distribution when coding a
forced (by interval) key frame. The result of this was that in some
cases, when allocating bits at the GF group level within a KF
group there was either a glut of bits or starvation of bits at the end
of the KF group.
Added code to rescan and get the correct data once the position of
a forced key frame has been determined.
Change-Id: I0c811675ef3f9e4109d14bd049d7641682ffcf11
vp8cx_mb_init_quantizer was being called for every mode checked
in vp8_rd_pick_inter_mode. zbin_extra is the only value that
really needs to be recalculated. This calculation is disabled
when using the fast quantizer for mode selection.
This gave a small performance boost (~.5% to 1%).
Note: This needs to be verified with segmentation_enabled.
Change-Id: I62716a870b3c82b4a998bdf95130ff0b02106f1e
In sub-pixel calculation, xoffset and yoffset mostly take some
specific values. Modified sub-pixel filter functions according to
these possible values to improve performance.
Change-Id: I83083570af8b00ff65093467914fbb97a4e9ea21
Added code to scan ahead a few frames when we see what
we think is a static scene in the two pass GF loop to see if the
conditions persist.
Moved calculation of decay rate out into a fuunction.
Change-Id: I6e9c67e01ec9f555144deafc8ae67ef25bffb449
These changes are specifically targeted at fade transitions to
static scenes. Here we want to place a GF/ARF immediately
after the fade and prevent an ARF just before the fade.
Also some code lines and comment lines shortened to 80 chars
while I was there.
Change-Id: Iefdc09a4fa7b265048fc017246b73e138693950f
In both vp8_find_next_key_frame and define_gf_group,
motion_pct was initialised at the top of the loop before
next_frame stats had been read in.
This fix sets motion_pct after next_frame stats have
been read.
Change-Id: I8c0bebf372ef8aa97b97fd35b42973d1d831ee73
Prior to this change, VP8 min quantizer is 4, which caps the
highest quality around 51DB. This experimental change extends
the min quantizer to 1, removes the cap and allows the highest
quality to be around ~73DB, consistent with the fdct/idct round trip
error. To test this change, at configure time use options:
--enable-experimental --enable-extend_qrange
The following is a brief log of changes in each of the patch sets
patch set 1:
In this commit, the quantization/dequantization constants are kept
unchanged, instead scaling factor 4 is rolled into fdct/idct.
Fixed Q0 encoding tests on mobile:
Before: 9560.567kbps Overall PSNR:50.255DB VPXSSIM:98.288
Now: 18035.774kbps Overall PSNR:73.022DB VPXSSIM:99.991
patch set 2:
regenerated dc/ac quantizer lookup tables based on the scaling
factor rolled in the fdct/idct. Also slightly extended the range
towards the high quantizer end.
patch set 3:
slightly tweaked the quantizer tables and generated bits_per_mb
table based on Paul's suggestions.
patch set 4:
fix a typo in idct, re-calculated tables relating active max Q
to active min Q
patch set 5:
added rdmult lookup table based on Q
patch set 6:
fix rdmult scale: dct coefficient has scaled up by 4
patch set 7:
make transform coefficients to be within 16bits
patch set 8:
normalize 2nd order quantizers
patch set 9:
fix mis-spellings
patch set 10:
change the configure script and macros to allow experimental code
to be enabled at configure time with --enable-extend_qrange
patch set 11:
rebase for merge
Change-Id: Ib50641ddd44aba2a52ed890222c309faa31cc59c
Incorrect value loop_decay_rate used in GF loop.
The intent was to test the cumulative value decay_accumulator.
Change-Id: I62928c63eb09f4f6936a45ebd1c23784d1c9681b
A new vpx_codec_control called VP8D_GET_FRAME_CORRUPTED. The output
from the function is non-zero if the last decoded frame contains
corruption due to packet losses.
The decoder is also modified to accept encoded frames of zero length.
A zero length frame indicates to the decoder that one or more frames
have been completely lost. This will mark the last decoded reference
buffer as corrupted. The data pointer can be NULL if the length is
zero.
Change-Id: Ic5902c785a281c6e05329deea958554b7a6c75ce
In vp8_find_best_sub_pixel_step_iteratively(), many times xoffset
and yoffset are specific values - (4,0) (0,4) and (4,4). Modified
code to call simplified NEON version at these specific offsets to
help with the performance.
Change-Id: Iaf896a0f7aae4697bd36a49e182525dd1ef1ab4d
This code fixes a bug in the calculation of
the minimum Q for alt ref frames.
It also allows an extended gf/arf interval for sections
of clips that completely static (or nearly so).
Change-Id: I1a21aaa16d4f0578e5f99b13bebd78d59403c73b
Remove allocation/deallocation of stats storage.
Remove full search functions in machine specific encoder inits.
Remove last pass validation in validate_config.
Change-Id: I7f29be69273981a4fef6e80ecdb6217c68cbad4e
The CQ level was not using the q_trans[] array to convert
to a 0-127 range as per min and maxq
Experimental change to try and match the reconstruction
error for forced key frames approximately to that of the
previous frame by means of the recode loop. Though this
may cause extra recodes and the recode behavior has not
been optimized, it can only happen on forced key frames.
Change-Id: I1f7e42d526f1b1cb556dd461eff1a692bd1b5b2f
Previously when a frame was being overlaid on a previously coded
alt ref frame we only checked the alt ref 0,0 mode. Where there is
a possibility that the alt ref buffer is a filtered frame we should allow
the other prediction modes as normal or at the least allow use of
the last frame buffer.
Change-Id: I4d6227223d125c96b4f3066ec6ec9484fee7768c
In cases where the frame width is not a multiple of 16 the
ARNR filter would go wrong.
In vp8_temporal_filter_iterate_c when updating pointers
at the end of a row of MBs, the image size was
incorrectly used rather than using Num_MBs_In_Row
times 16 (Y) or 8 (U,V).
This worked when width is multiple of 16 but failed
otherwise.
Change-Id: I008919062715bd3d17c7aa2562ab58d1cb37053a
This change is designed to try and reduce pulsing effects when moving
with a complex transition like a fade, into an easy or static section in
an otherwise difficult clip in CQ mode.
The active CQ level is relaxed down to the user entered level for frames that
are generating less than the passed in minimum bandwidth.
Change-Id: Id6d8b551daad4f489c087bd742bc95418a95f3f0
Fixed discrepancy cpi->ni_frames vs cm->current_video_frame > 150.
Make one pass path explicit.
There is still scope for some odd behaviour around the transition
point at cpi->ni_frames > 150.
Change-Id: Icdee130fe6e2a832206d30e45bf65963edd7a74d
Where a key frame occurs because of a minimum interval
selected by the user, then these forced key frames ideally need
to be more closely matched in quality to the surrounding frame.
Change-Id: Ia55b1f047e77dc7fbd78379c45869554f25b3df7
Add a flag to always enable block4x4 search for speed=0 (good
quality) to guarantee no quality loss for speed0.
Change-Id: Ie04bbc25f7e6a33a7bfa30e05775d33148731c81
The maximum possible MV in 1/8 pel units is (1<<11), which could
cause mvcost out of its range that is 1023. Change maximum
possible MV in 1/8 pel units to (1<<11)-8 will fix this problem.
Change-Id: I5788ed1de773f66658c14f225fb4ab5b1679b74b
Further experiment with restriction of the Q range.
This uses the average non KF/GF/ARF quantizer, instead
of just relying on the initial value. It is not such a strong constraint
but there may be a reduced risk of rate misses.
Change-Id: I424fe782a37a2f4e18c70805e240db55bfaa25ec
The merge includes hooks to for CQ mode and other code
changes merged from the test branch.
CQ mode attempts to maintain a more stable quantizer within a clip
whilst also trying to adhere to a guidline maximum bitrate.
The existing target data rate parameter is used to specify the
guideline maximum bitrate.
A new parameter allows the user to specify a target CQ level.
For normal (non kf/gf/arf) frames, the quantizer will not drop BELOW the
user specified value (0-63). However, in some cases the encoder may
choose to impose a target CQ that is above that specified by the user,
if it estimates that consistent use of the target value is not compatible
with guideline maximum bitrate.
Change-Id: I2221f9eecae8cc3c431d36caf83503941b25e4c1
In two pass encoding each frame is given an active
Q range to work with. This change limits how much this
Q range can be altered over time from the initial estimate
made for the clip as a whole.
There is some danger this could lead to overshoot or undershoot
in some corner cases but it helps considerably in regard to
clips where either there is a glut or famine of bits in some sections,
particularly near the end of a clip.
Change-Id: I34fcd1af31d2ee3d5444f93e334645254043026e
cpi->target_bits_per_mb is currently not being used,
so delete it. Also removed other unused code in rdopt.c.
Change-Id: I98449f9030bcd2f15451d9b7a3b9b93dd1409923
count can be reduced to short because the max number of filtered frames
is set to 15. the max value for any frame is 32 (modifier = 16,
filter_weight = 2). 15*32 = 480 which requires 9 bits
this function goes from about 7000 us / 1000 iterations for the C code
to < 275 us / 1000 iterations for sse2 for block_size = 16 and from
about 1800 us / 1000 iters to < 100 us / 1000 iters for block_size = 8
Change-Id: I64a32607f58a2d33c39286f468b04ccd457d9e6e
Commit 0ce3901 introduced a change in the frame buffer copy logic where
the NEW frame could be copied to the ARF or GF buffer through the
copy_buffer_to_{arf,gf}==1 flags, if the LAST frame was not being
refreshed. This is not correct. The intent of the
copy_buffer_to_{arf,gf}==1 flag is to copy the LAST buffer. To copy the
NEW buffer, the refresh_{alt_ref,golden}_frame flag should be used.
The original buffer copy logic is fairly convoluted. For example:
if (cm->refresh_last_frame)
{
vp8_swap_yv12_buffer(&cm->last_frame, &cm->new_frame);
cm->frame_to_show = &cm->last_frame;
}
else
{
cm->frame_to_show = &cm->new_frame;
}
...
if (cm->copy_buffer_to_arf)
{
if (cm->copy_buffer_to_arf == 1)
{
if (cm->refresh_last_frame)
vp8_yv12_copy_frame_ptr(&cm->new_frame, &cm->alt_ref_frame);
else
vp8_yv12_copy_frame_ptr(&cm->last_frame, &cm->alt_ref_frame);
}
else if (cm->copy_buffer_to_arf == 2)
vp8_yv12_copy_frame_ptr(&cm->golden_frame, &cm->alt_ref_frame);
}
Effectively, if refresh_last_frame, then new and last are swapped, so
when "new" is copied to ARF, it's equivalent to copying LAST to ARF. If
not refresh_last_frame, then LAST is copied to ARF. So LAST is copied to
ARF in both cases.
Commit 0ce3901 removed the first buffer swap but kept the
refresh_last_frame?new:last behavior, changing the sense since the first
swap wasn't done to the more readable refresh_last_frame?last:new, but
this logic is not correct when !refresh_last_frame.
This commit restores the correct behavior from v0.9.1 and prior. This
case is missing from the test vector set.
Change-Id: I8369fc13a37ae882e31a8a104da808a08bc8428f
The following features don't make sense for the first
pass in its current form and have a significant impact on its
speed (up to 50%).
Slow quantizer, slow dct and trellis optimization.
Change-Id: Id9943f6765ffbd71fc0084ec7dfbc9d376fd6fcd
Calculate a minimum intra value to be used in determining the
IIratio scores used in two pass, second pass.
This is to make sure sections that are low complexity" in the
intra domain are still boosted appropriately for KF/GF/ARF.
For now I have commented out the Q based adjustment of
KF boost.
Change-Id: I15deb09c5bd9b53180a2ddd3e5f575b2aba244b3
Scott pointed out that last_frame_type only gets updated while
loopfilter exists. Since last_frame_type is also needed in
motion search now, it needs to be updated every frame.
Change-Id: I9203532fd67361588d4024628d9ddb8e391ad912
Use the fast quantizer for inter mode selection and the
regular quantizer for the rest of the encode for good quality,
speed 1. Both performance and quality were improved. The
quality gains will make up for the quality loss mentioned in
I9dc089007ca08129fb6c11fe7692777ebb8647b0.
Change-Id: Ia90bc9cf326a7c65d60d31fa32f6465ab6984d21
1. Search for block8x16/block16x8 uses block8x8's search results.
2. Check block4x4 only if block8x8 is chosen. (This hurts quality,
which will be improved in another check-in.)
3. In block4x4 search, the previous block's result is used as
MV predictor for next block.
This change improves performance.
Change-Id: I9dc089007ca08129fb6c11fe7692777ebb8647b0
Re-calibrated sad_per_bit16 and sad_per_bit4 tables to linearly
correlated to quantizer values, these two variables are used in
motion search for costing motion vectors. This change has an small
positive effect on compression.
Change-Id: Ic9b5ea6fb8d5078ef663ba4899db019cc51f4166
the lookup table is based on floating point calculations (see source)
by moving the *3 before the downshift and adding the rounding bit, the
delta (LUT - integer) goes from:
______________________________________
__ 1__ 1______________________________
__ 1__ 1______________________________
____ 1______ 1________________________
____ 1 2__ 2 1________________________
______ 1 1 2__ 2__ 2__ 2 1 1__________
________ 1 1 2 2__ 1 2 3 1 2__ 2__ 2__
to:
__-1__-1______________________________
______________________________________
____-1______-1________________________
______________________________________
________-1______________-1____________
______________________________________
it's important to be able to use the integer version because the LUT
more or less precludes SIMD optimizations
Change-Id: I45a81127dc7b72a06fba951649135d9d918386c0
allow for optimized versions of apply_temporal_filter
(now vp8_apply_temporal_filter_c)
the function was previously declared as static and appears to have been
inlined. with this change, that's no longer possible. performance takes
a small hit.
the declaration for vp8_cx_temp_filter_c was moved to onyx_if.c because
of a circular dependency. for rtcd, temporal_filter.h holds the
definition for the rtcd table, so it needs to be included by onyx_int.h.
however, onyx_int.h holds the definition for VP8_COMP which is needed
for the function prototype. blah.
Change-Id: I499c055fdc652ac4659c21c5a55fe10ceb7e95e3
The pointer passed in the user_priv argument to vpx_codec_decode()
should be propagated through to the corresponding output frame and
made available in the image's user_priv member. Fixes issue #252
Change-Id: I182746a6882c8549fb146b4a4fdb64f1789eb750
Add a new encoder control, VP8E_SET_TUNING, to allow the application
to inform the encoder that the material will benefit from certain
tuning. Expose this control as the --tune option to vpxenc. The args
helper is expanded to support enumerated arguments by name or value.
Two tunings are provided by this patch, PSNR (default) and SSIM.
Activity masking is made dependent on setting --tune=ssim, as the
current implementation hurts speed (10%) and PSNR (2.7% avg,
10% peak) too much for it to be a default yet.
Change-Id: I110d969381c4805347ff5a0ffaf1a14ca1965257
Inform the caller of the decoder if a decoded frame updated last,
golden, or altref frames, required for realtime communication
proposed in document VP8 RTP payload format.
Added a new vpx_codec_control called VP8D_GET_LAST_REF_UPDATES, to be
called after vpx_codec_decode. The control will indicate which of the
reference frames that were updated by setting the 3 LSBs in the input
int (pointer).
Change-Id: Iac9db60dac414356c7ffa0b0fede88cb91e11bd7
In SPLITMV, the 8x8 segment will be checked first. If the 8x8 rd
is better than the best, we check the other segments. Otherwise
bail. Adjustments to the thresh_mult were necessary to make
up for the initial quality loss.
The performance improved by 20% (average) for good quality,
speed 0 and speed 1, while the overall quality remained the same.
Change-Id: I717aef401323c8a254fba3e9777d2a316c774cc3
vp8_rd_pick_best_mbsegmentation looks at y only. The new
breakout does not include the frame cost, the prob_skip_false
cost, or the uv rate. Performance improved by a few percent
and the quality remained the same.
Change-Id: I94ff013998ac51e8ecce7130870f7b6600758e15
This fix added MV range checks for NEWMV mode as suggested by Jim.
To reduce unnecessary MV range checks, I tried Yaowu's suggestion.
Update UMV borders in NEWMV mode to also cover MV range check.
Also, in this way, every MV that is valid gets checked in diamond
search function.
Change-Id: I95a89ce0daf6f178c454448f13d4249f19b30f3a
The MV's range is 256. Since the new motion search uses a different
starting MV than the center ref MV, a MV range checking needs to
be done to avoid corruption.
Change-Id: I8ae0721d1bd203639e13891e2e54a2e87276f306
Per John's previous change, shrink TOKENEXTRA from 20 to 8 bytes
original: b7b1e6fb
reverted: 41f4458a
Also drop unused field from vp8_extra_bit_struct
Update ARM ASM to deal with this change. In particular, Extra is signed
and needs to be sign-extended when loaded.
Change-Id: Ibd0ddc058432bc7bb09222d6ce4ef77e93a30b41
This code is unused, as the current preproc implementation uses the
same spatial filter that postproc uses.
Change-Id: Ia06d5664917d67283f279e2480016bebed602ea7
Change the size of structure elements to reduce memory utilization.
Removed the 'section' member entirely, as it is set but never read.
Change-Id: Iad043830392fb4168cb3cd6075fb0eb70c7f691c
Added the initialization of the pointer to active map. Also added the
same logic for cyclic refresh in mbrow encoding threads.
Change-Id: Ic48d0849dc706b27fba72d07dcc498075725663d
Changed the end of block computation to use pmaxw. Removed
additional pushing and popping of registers that was not needed.
Change-Id: I08cb9b424513cd8a2c7ad8cea53b4e2adc66ef98
Change I3430820 performed an uninitialized read when
encode_breakout == 0, since the sum and sse wouldn't be set:
if(x->encode_breakout)
VARIANCE_INVOKE(..., get16x16var)(..., &sum, &sse);
if (cpi->active_map_enabled && x->active_ptr[0] == 0) {
...
} else if (sse < x->encode_breakout)
Change-Id: I915eb76d1227b4b6d1137a0dedf2c143860098a2
Corrected the initial Q range limits for the recode loop
to reflect the current allowed range for the frame.
In experimental work on constrained quality this bug was
causing unnecessary recodes.
Change-Id: I7e256fbfa681293b0223fe21ec329933d76c229f
This patch adds a weighting factor on RDMULT for UV blocks. The change
has an overall gain about 0.5% based on ssim, between 0.1 and 0.2% by
psnr numbers.
Change-Id: I97781b077ce3bb7e34241b03268491917e8d1d72
Deallocating the buffers before re-allocating them.
The fix passed James Berry's test program for memory
leak check.
Change-Id: I18c3cf665412c0e313a523e3d435106c03ca438d
Moved the code from the segmentation loop into a function
which is now called for each segment. This will allow us
to change the segment order checking more easily.
Change-Id: I9510d26f0acae5a73043fcca8f1984b121d3e052
When auto_golden wasn't set it forced all frames to be a golden
frame. Now the manual configured frequency is adhered to.
Change-Id: I360acac9bc487db0d9c4d4da6ee41f70c227c539
The inter_minq table controls the range of quantizers available
for a particular frame in two pass relative to a max Q value.
The changes reduces the range somewhat. The effect of this
was a small increase (0.3% average) in psnr for the test set
but it should also help encode speed somewhat for higher
quality modes as it will reduce the number of iterations in the
recode loop.
The change damps the range of quantizers available locally
within a section of a clip and should therefore help keep quality
more uniform. If there is systematic overshoot or undershoot the
range can shift gradually to accommodate. However, there is
some increased risk of overshoot or undershoot against the target
bit rate in VBR mode and this risk will be more pronounced for short
clips.
The change damps the range of quantizers available locally
within a section of a clip and should therefore help keep quality
more uniform. If there is systematic overshoot or undershoot the
range can shift gradually to accommodate. However, there is
some increased risk of overshoot or undershoot against the
target bit rate in VBR mode and this risk will be more
pronounced for short clips.
Change-Id: I84465567d49ae767c6c73ff2a2aac30c895adb52
Add vp8_mv_pred() to better predict starting MV for NEWMV
mode in vp8_rd_pick_inter_mode(). Set different search
ranges according to MV prediction accuracy, which improves
encoder performance without hurting the quality. Also,
as Yaowu suggested, using diamond search result as full
search starting point and therefore adjusting(reducing)
full search range helps the performance.
Change-Id: Ie4a3c8df87e697c1f4f6e2ddb693766bba1b77b6
On a keyframe alt ref and golden are refreshed. The flag was
not being set and so on the frame after a keyframe, motion
search would occur on the alt ref frame. This is not necessary
because the alt ref frame identical to the last frame in this
scenario.
Handle corner case where a forward alt-ref frame is put
directly after a keyframe.
Change-Id: I9be4cf290d694f8cf2f9a31852014b5ccf1504d3
remove warning comment in vpxenc.c: in case of 1x1 picture,
detect_bytes will be equal to '3' and we'll fall back to
RAW_TYPE.
fix read_frame() by tracking the pre-read buffer length
in the struct detect
Change-Id: If1ed86ee5260dcdbc8f9d10da6cbb84a4cc2f151
The baseline bits per MB prediction tables have been
re calibrated based on the assumption that bits per mb
is inversely proportional to the quantizer level.
Change-Id: Ibd355c7acac4b8053dda1baf1032fe35f11da7f7
