Coding and costing of mv reference signal.
Issues in updating MV ref with COMPANDED_MVREF_THRESH
to be resolved. Ideally the MV precision should be defined based
on absolute MV magnitude not as now the MV ref magnitude.
Update to mv counts moved into bitstream.c because otherwise
if the motion reference is changed at the last minute the encoder
and decoder get out of step in terms of the counts used to update
entropy probs.
Code working on a few test clips but no results yet re benefit vs
signaling cost and no tuning of red loop to test lower cost alternatives
based on the available reference values.
Patch 3. Added check to make sure we don't pick a reference
that would give rise to an uncodeable / out of range residual.
Patch 6-7: Attempt to rebase. OK to submit but best to leave flag off for now.
Patch 9. Remove print no longer needed.
Change-Id: I1938c2ffe41afe6d3cf6ccc0cb2c5d404809a712
Refactor per-transform copy & paste into a common function
update_coef_probs_common() and read_coef_probs_common(). The dry-run and
bit-writing loops in the encoder are still obvious candidates to be made
common, but they start to diverge a bit in the next commit, so are left
as-is for now.
Change-Id: I896bd3f4a073a6296eab7e92463fef79d8c6c08c
There is a macro DEFAULT_INTERP_FILTER defined in encoder/onyx_if.c that
is set as EIGHTTAP for now - so SWITCHABLE is not really used. Ideally,
this should be SWITCHABLE but that would make the encoder quite a bit slower.
We will change the default filter to SWITCHABLE once we find a faster way to
search for switchable filters.
Change-Id: Iee91832cdc07e6e14108d9b543130fdd12fc9874
* changes:
Fix another typo in 4x4-transform-for-i8x8-intra-pred coeff contexts.
8x8 transform support in splitmv.
Use SPLITMV_PARTITIONING instead of a plain integer type.
For splitmv, where partitioning is 8x16, 16x8 or 8x8, this patch
uses the 8x8 transform (instead of the 4x4) if txfm_mode is
ALLOW_8X8 or ALLOW_16X16. For TX_MODE_SELECT, splitmv can indicate
which of the 2 transform sizes (4x4 or 8x8) it wants to use.
Gains (with hybridtx4x4/8x8/16x16 and tx_select experiments
enabled) on derf: +0.9%, HD: +0.4%, STD/HD: +0.8% (SSIM or overall
PSNR, both metrics show similar improvements).
Change-Id: Ide954b000b415548ed92a7ac78e24f36e60fcf06
Allows B_VL_PRED & B_LD_PRED modes to be used for all blocks
within a MB in B_PRED mode. These modes were temporarily
disabled with super-block coding.
Change-Id: I973b9bdb82c3da5f12d7cc963162a28805f25303
Pass the bool coder to be used explicitly. This avoids cases where two
different bool coders can be addressed from the same function. Also be
more consistent with bool coder variable naming, start to standardize
on 'bc'.
Change-Id: I1c95e2fdbe24ebe8c0f84924daa1728e3b054a31
Separates the logic on transform type selection previously spread out
over a number of files into a separate function. Currently the tx_type
field in b_mode_info is not used, but still left in there to eventually
use for signaling the transform type in the bitstream.
Also, now for tx_type = DCT_DCT, the regular integer DCT is used, as
opposed to the floating point DCT used in conjuction with hybrid
transform.
Results change somewhat due to the transform change, but are within
reasonable limits. The hd/std-hd sets are slightly up, while derf/yt
are slightly down.
Change-Id: I5776840c2239ca2da31ca6cfd7fd1148dc5f9e0f
This commit moves a bit of data that ended up packed with the
modes/mv/residual partition during the change to interleaved encoding
into partition 0 where it belongs.
Change-Id: Ic711a378c58d9d6a17254384f492c213a15bad92
Packs the bitstream with each mb's residual following its mode/mv
information.
TODO: There are still a few fields that should be packed into partition
0 but are included in partition 1, due to them being serialized from
write_kfmodes/pack_inter_mode_mvs, which execute after the first
partition is finalized. These need to be separated out into a separate
function, similar to mb_mode_mv_init() in decodemv.c.
Change-Id: I43a46c363601ab36954d07ebe498760e1e2e3af4
Rather than decoding all modes/mvs separately, decode them per MB. This
forces the mode which was already used form the CONFIG_NEWBESTREFMV and
CONFIG_SUPERBLOCKS experiments, and is a precursor to changing to
interleaved encoding.
Change-Id: If19ee74ac8a987846d1cd0cf2b2e02a82f1a43ad
Change the macros PLANE_TYPE_{Y_NO_DC,Y2,UV,Y_WITH_DC} to a typed enum,
and use this typed enum consistently across all places where relevant.
In places where the type is implied (e.g. in functions that only handle
second order planes or chroma planes), remove it as a function argument
and instead hardcode the proper enum in the code directly.
Change-Id: I93652b4a36aa43163d49c732b0bf5c4442738c47
The update_mb_segmentation_map flag was being signalled earlier than
other data dependent on that flag. Consolidate this data so it's
parsed within the same if-scope as the flag is originally parsed in.
Change-Id: I10e90b4f511856445ef75a85a44ff441e1e5e672
Results: derf (vanilla or +hybridtx) +0.2% and (+hybrid16x16
or +tx16x16) +0.7%-0.8%; HD (vanilla or +hybridtx) +0.1-0.2%
and (+hybrid16x16 or +tx16x16) +1.4%, STD/HD (vanilla or +hybridtx)
about even, and (+hybrid16x16 or +tx16x16) +0.8-1.0%.
Change-Id: I03899e2f7a64e725a863f32e55366035ba77aa62
Separates the entropy coding context models for 4x4, 8x8 and 16x16
ADST variants.
There is a small improvement for HD (hd/std-hd) by about 0.1-0.2%.
Results on derf/yt are about the same, probably because there is not
enough statistics.
Results may improve somewhat once the initial probability tables are
updated for the hybrid transforms which is coming soon.
Change-Id: Ic7c0c62dacc68ef551054fdb575be8b8507d32a8
With this change, even if hybridtransform8x8 experiment is off,
8x8 dct is used for the I8x8 mode. However note that the gains
observed with the hybridtransform8x8 experiment will now be less,
since part of the gain is now merged in.
Change-Id: I9afb3880906fd0a1368a374041fc08efcf060c54
The high-precision (1/8) pel bit is turned off if the reference
MV is larger than a threshold. The motivation for this patch is
the intuition that if motion is likely large (as indicated by
the reference), there is likley to be more motion blur, and as
a result 1/8 pel precision would be wasteful both in rd sense
as well as computationally.
The feature is incorporated as part of the newmventropy experiment.
There is a modest RD improvement with the patch. Overall the
results with the newmventropy experiment with the threshold being
16 integer pels are:
derf: +0.279%
std-hd: +0.617%
hd: +1.299%
yt: +0.822%
With threshold 8 integer pels are:
derf: +0.295%
std-hd: +0.623%
hd: +1.365%
yt: +0.847%
Patch: rebased
Patch: rebase fixes
Change-Id: I4ed14600df3c457944e6541ed407cb6e91fe428b
Some cleanups that will make it easier to maintain the code
and incorporate upcoming changes on entropy coding for the
hybrid transforms.
Change-Id: I44bdba368f7b8bf203161d7a6d3b1fc2c9e21a8f
This commit merges those parts of the CONFIG_NEW_MVREF
that specifically relate to choosing a better set of candidate
MV references into the NEWBESTREFMV experiment.
CONFIG_NEW_MVREF will then be used for changes relating
to the explicit coding of a cost optimized MV reference in the
bitstream as part of MV coding.
Change-Id: Ied982c0ad72093eab29e38b8cd74d5c3d7458b10
Extend experiment to use both vectors from MBs
coded using compound prediction as candidates.
In final sort only consider best 4 candidates
for now but make sure 0,0 is always one of them.
Other minor changes to new MV reference code.
Pass in Mv list to vp8_find_best_ref_mvs().
Change-Id: Ib96220c33c6b80bd1d5e0fbe8b68121be7997095
Adds a new experiment with redesigned/refactored motion vector entropy
coding. The patch also takes a first step towards separating the
integer and fractional pel components of a MV. However the fractional
pel encoding still depends on the integer pel part and so they are
not fully independent. Further experiments are in progress to see
how much they can be decoupled without affecting performance.
All components including entropy coding/decoding, costing for MV
search, forward updates and backward updates to probability tables,
have been implemented.
Results so far:
derf: +0.19%
std-hd: +0.28%
yt: +0.80%
hd: +1.15%
Patch: Simplifies the fractional pel models:
derf: +0.284%
std-hd: +0.289%
yt: +0.849%
hd: +1.254%
Patch: Some changes in the models, rebased.
derf: +0.330%
std-hd: +0.306%
yt: +0.816%
hd: +1.225%
Change-Id: I646b3c48f3587f4cc909639b78c3798da6402678
Enable ADST/DCT of dimension 16x16 for I16X16 modes. This change provides
benefits mostly for hd sequences.
Set up the framework for selectable transform dimension.
Also allowing quantization parameter threshold to control the use
of hybrid transform (This is currently disabled by setting threshold
always above the quantization parameter. Adaptive thresholding can
be built upon this, which will further improve the coding performance.)
The coding performance gains (with respect to the codec that has all
other configuration settings turned on) are
derf: 0.013
yt: 0.086
hd: 0.198
std-hd: 0.501
Change-Id: Ibb4263a61fc74e0b3c345f54d73e8c73552bf926
