Disable zbin boost in SPLITMV mode as intended. Was incorrectly looking
at vp8_ref_frame_order instead of vp8_mode_order when comparing against
SPLITMV. This condition should have always been false, as SPLITMV is
not in the range of valid reference frames.
Change-Id: I0408cc7595eff68f00efef6d008e79f5b60d14bf
In some cases where clips have been encoded with
borders (eg. some wide-screen content where there is a
border top and bottom and slide shows containing portrait
format photographs (border left and right)) key frames were
not being correctly detected.
The new code looks to measure cases where a portion of
the image can be coded equally easily using intra or inter
modes and where the resulting error score is also very low.
These "neutral" areas are then discounted in the key frame
detection code.
Change-Id: I00c3e8230772b8213cdc08020e1990cf83b780d8
This code extends what was previously done for GFs, to pick
cases where insertion of a key frame after a fade (or other
transition or complex motion) followed by a still section, will
be beneficial and will reduce the number of forced key frames.
Change-Id: If8bca00457f0d5f83dc3318a587f61c17d90f135
When the modified_error_left accumulator exceeds INT_MAX, an incorrect
cast to int resulted in a negative value, causing the rate control to
allocate no bits to that keyframe group, leading to severe undershoot
and subsequent poor quality.
This error was exposed by the recent change to the rolling target and
actual spend accumulators in commit 305be4e4 which fixed them to
actually calculate the average value rather than be re-initialized
on every frame to the average per-frame bitrate. When this bug was
triggered, the target bitrate could be 0, so the rolling target
becomes small, which causes the undershoot. The code prior to 305be4e4
did not exhibit this behavior because the rolling target was always
set to a reasonable value and was independent of the actual target
bitrate. With this patch, the actual target bitrate is calculated
correctly, and the rate control tracks as expected.
This cast was likely added to silence a compiler warning on a comparison
between a double (modified_error_left) and an int (0). Instead, this
patch removes the cast and changes the comparison to be against 0.0,
which should prevent the warning from reoccuring.
This fixes issue #289. Special thanks to gnafu for his efforts in
reporting and debugging this fix.
Change-Id: Ie5cc1a7b516c578a76c3a50c892a6f04a11621fe
This fixes an overflow problem in the frame error accumulators.
The overflow condition is extreme but did trigger when Frank B.
coded some high motion interlaced HD content.
The observed effect was a catastrophic breakdown of the rate
control leading to massive undershoot and poor bit allocation.
All the error values should really be unsigned but I will look at this
separately.
Change-Id: I9745f5c5ca2783620426b66b568b2088b579151f
Currently, when the video frame width is not multiples of 16, the
source buffer has a stride of non-multiples of 16, which forces
an unaligned load in SAD function and hurts the performance. To
avoid that, this change allocates source buffers to be multiples
of 16.
Change-Id: Ib7506e3eb2cea06657d56be5a899f38dfe3eeb39
In real-time mode, vp8_sad16x16 function is called heavily in
motion search part. Improvement of this function gives 1.2%
encoding performance gain (real-time mode, tulip clip).
Change-Id: I23c401fc40c061f732a9767e8d383737a179bd58
checks added to make sure that cpi->tplist
is freed correctly in vp8_dealloc_compressor_data
and vp8_alloc_compressor_data.
Change-Id: I66149dbbd25c958800ad94f4379d723191d9680d
Eliminated unnecessary calculations. Improved performance
by 10% on keyframes and 1.6% overall for the test clip used.
Change-Id: I87671b26af5e2cc439e81d0fee3b15c7cd2a3309
As mentioned in check-in "Improve motion search in real-time mode",
MV prediction calculation causes speed loss for speed 7 and above.
This change added a flag to turn off this calculation for speed>6
in real-time mode.
Change-Id: I9f4ae5a8bf449222d1784b54e7d315fc8347b2d1
Applied better MV prediction in real-time mode, which improves
the encoding quality.
Used quarter-pixel search instead of iterative sub-pixel search
for speed >=5 to improve encoding performance.
Tests on the test set showed:
1. For speed=-5, quality improvement: 1.7% on AvgPSNR and 2.1%
on SSIM, performance improvement: 3.6% (This counts in the
performance lose caused by MV prediction calculation in "Improve
MV prediction in vp8_pick_inter_mode() for speed>3").
2. For speed=-8, quality improvement: 2.1% on AvgPSNR and 2.5%
on SSIM. but, 6.9% performance decrease because of MV prediction
calculation. This should be improved later.
Change-Id: I349a96c452bd691081d8c8e3e54419e7f477bebd
Created a new speed 1 which is in the middle of the old
speed 0 and speed 1. (for both quality and performance)
Change-Id: I4802133cdb43f359ca787646c090899679dd5d84
Use 0xFFF0 vice 240 (0xF0) for determining whether the sometimes
implicit bit 3 will be transmitted. This is consistent with the decoder
and encode_mvcomponent().
Change-Id: Ic1304d0ab56844bed8236edd1c5243a6767fc6b1
make reference version of bilinear_filters short.
use reference versions of bilinear_filters and sub_pel_filters when
possible.
recognize that Width was being passed into
filter_block2d_bil_first_pass multiple times. ARM version had already
fixed this. propegate to C.
change references to src_pixels_per_line to src_pitch and standardize on
src/dst (instead of input/output).
recognize that first_pass is only run in the verticle and second_pass
only horizontal. ARM version had already fixed this. propegate to C
Change-Id: I292d376d239a9a7ca37ec2bf03cc0720606983e2
it's difficult to mux the *_offsets.c files because of header conflicts.
make three instead, name them consistently and partititon the contents
to allow building them as required.
Change-Id: I8f9768c09279f934f44b6c5b0ec363f7943bb796
preview_img d_w and d_h along with w and h
would not be updated for resized frames.
now uses sd.y_width and sd.y_height
Change-Id: I52241de4cc1de5e73f865e668bd70a7cbd954390
When the keyframe distance is fixed the first interval has the right
distance but, the next ones have kf_distance + 1.
Change-Id: I44f1190fe7146124bd07660a5e0ef08829e3ae07
common/arm/vpx_asm_offsets moves up a level. prepare for muxing with
encoder/arm/vpx_vp8_enc_asm_offsets
Change-Id: I89a04a5235447e66571995c9d9b4b6edcb038e24
The encoder was not correctly catching transitions in the quantizer
deltas. If a delta_q was set, then the quantizer would be reinitialized
on every frame, but if they transitioned to 0, the quantizer would
not be reinitialized, leading to a encode-decode mismatch.
This bug was triggered by commit 999e155, which sets a Y2 delta Q
for very low base Q levels.
Change-Id: Ia6733464a55ee4ff2edbb82c0873980d345446f5
Whe auto keyframe insertion is enabled and conditions are right (scene change)
the encoder can decide to insert a key frame and does a re-encoding. This can
introduce extra latency. In RT mode we do not do the re-encoding of the current
frame but force the next frame to key frame.
Change-Id: I15c175fa845ac4c1a1f18bea3676e154669522a7
Reduce the number of sync points by letting each thread
continue imediatly with a new MB row.
Better multicore scaling, improves performance by 5-20% on ARM multicore.
Change-Id: Ic97e4d1c4886a842c85dd3539a93cb217188ed1b
from vp8cx_encode_intra_macro_block. prediction_error is used when
deciding if a frame should be a keyframe. After reviewing this with
Yaowu, it was pointed out that vp8cx_encode_intra_macro_block
is only called for keyframes, so the accumulation is unnecessary.
Change-Id: Id79dc81b80d4f5d124f3a0dba1b923887e2e1ec8
vp8_pick_intra4x4mby_modes uses the passed in distortion
for an early breakout. The best distortion was never saved
and the distortion for TM_PRED was always used.
Change-Id: Idbaf73027408a4bba26601713725191a5d7b325e
