Add support for setting byte alignment on the Y, U, and V plane of the
reference buffers. The byte alignment must be a power of 2, from 32 to
1024. A value of 0 sets legacy alignment.
Change-Id: I7c1399622f7aa68e123646369216b32047dda73d
the entire module is wrapped in CONFIG_VP9_POSTPROC which is forcibly
enabled with CONFIG_INTERNAL_STATS
+ a similar change in vp9_alloccommon.c
Change-Id: I374993297a9fba5bef2f0b71f984eba42f0995a3
If decoding starts with intra-only frame, there is a possibility
of using uninitialized entropy context, what leads to undefined
behavior.
Change-Id: Icbb64b5b1bd1e5de2a4bfa2884e56bc0a20840af
The 8x8 DCT uses a fast version whenever possible.
There was a mistake in the checking code which
meant sometimes the fast version was used when it
was not safe to do so.
Change-Id: I154c84c9e2d836764768a11082947ca30f4b5ab7
(cherry picked from commit fd05fb0c21e253b4d6f92d7e0b752850ff8ab188)
It is the first version of MFQE in VP9. There are a few TODOs included
in this version.
Usage: Add flag --enable-vp9-postproc to config the project.
In decoder, use flag --mfqe in the command line to enable
MFQE in postproc.
Note: Need to have key frame with low quality to see the effect of this
new patch. In my experiment, I fixed the qindex to 200 in key frame.
Change-Id: I021f9ce4616ed3574c81e48d968662994b56a396
The warning only happens in VP9 encoder's first pass due to src_mi
is not set up yet. But it will not fail the encoder as left_mi and
above_mi are not used in the first_pass and they will be set up again
in the second pass.
Change-Id: I12dffcd5fb1002b2b2dabb083c8726650e4b5f08
The function vp9_filter_block1d16_h8_ssse3 uses the PSHUFB instruction which has a 3 cycle latency and slows execution when done in blocks of 5 or more on Atom processors.
By replacing the PSHUFB instructions with other more efficient single cycle instructions (PUNPCKLBW + PUNPCHBW + PALIGNR) performance can be improved.
In the original code, the PSHUBF uses every byte and is consecutively copied.
This is done more efficiently by PUNPCKLBW and PUNPCHBW, using PALIGNR to concatenate the intermediate result and then shift right the next consecutive 16 bytes for the final result.
For example:
filter = 0,1,1,2,2,3,3,4,4,5,5,6,6,7,7,8
Reg = 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
REG1 = PUNPCKLBW Reg, Reg = 0,0,1,1,2,2,3,3,4,4,5,5,6,6,7,7
REG2 = PUNPCHBW Reg, Reg = 8,8,9,9,10,10,11,11,12,12,13,13,14,14,15,15
PALIGNR REG2, REG1, 1 = 0,1,1,2,2,3,3,4,4,5,5,6,6,7,7,8
This optimization improved the function performance by 23% and produced a 3% user level gain on 1080p content on Atom processors.
There was no observed performance impact on Core processors (expected).
Change-Id: I3cec701158993d95ed23ff04516942b5a4a461c0
Change 72193 made the encoder behave differently
when configured with and without high bitdepth.
This change means the same algorithm is used for both.
Change-Id: I707a44a94afca773a9e0c2f7ebeeea83030257c5
For key frame at speed 6: enable the non-rd mode selection in speed setting
and use the (non-rd) variance_based partition.
Adjust some logic/thresholds in variance partition selection for key frame only (no change to delta frames),
mainly to bias to selecting smaller prediction blocks, and also set max tx size of 16x16.
Loss in key frame quality (~0.6-0.7dB) compared to rd coding,
but speeds up key frame encoding by at least 6x.
Average PNSR/SSIM metrics over RTC clips go down by ~1-2% for speed 6.
Change-Id: Ie4845e0127e876337b9c105aa37e93b286193405
Also removes some spurious changes in common/vp9_blockd.h which
was introduced by a rebase issue between nextgen and master branches.
Change-Id: If359f0e9a71bca9c2ba685a87a355873536bb282
(cherry picked from commit 005d80cd05269a299cd2f7ddbc3d4d8b791aebba)
(cherry picked from commit 08d2f548007fd8d6fd41da8ef7fdb488b6485af3)
(cherry picked from commit 4230c2306c194c058f56433a5275aa02a2e71d56)
This change is made in preparation for a
subsequent patch which adds acceleration
for the highbitdepth transform functions.
The highbitdepth transform functions attempt
to use 16/32bit sse instructions where possible,
but fallback to using the C implementations if
potential overflow is detected. For this reason
the dct routines are made global so they can be
called from the acceleration functions in the
subsequent patch.
Change-Id: Ia921f191bf6936ccba4f13e8461624b120c1f665
(cherry picked from commit 454342d4e77dbb67f4a3c10f97a57a6fcb46d9a0)
Also includes block error.
(This patch is mostly cherry picked from
commit db7192e0b014a331a1dcb102c8a1148e9f0e1081)
Change-Id: Idef18f90b111a0d0c9546543d3347e551908fd78
This commit reworks the forward transform and quantization process
for 8x8 block coding. It combines the two operations in a single
function to save a store/load stage of the original transform
coefficients. Overall the speed -6 is slightly faster (around 1%
range). The compression performance of speed -6 is improved by
3.4%.
Change-Id: Id6628daef123f3e4649248735ec2ad7423629387
vp9_quantize_fp is the quantization process used by rtc coding
mode. This commit adds a sse2 implementation of it. The
implementation is modified based on vp9_quantize_b_sse2. No speed
difference from ssse3 version.
Change-Id: I24949c5b27df160b4f35117d28858d269454e64a
The function pointer in compressor instance does not change, so this
commit changes to call the function directly.
Change-Id: I9c9c460e3475711c384b74c9842f0b4f3d037cc5
