A large number of functions were defined with external linkage, even
though they were only used from within one file. This patch changes
their linkage to static and removes the vp8_ prefix from their names,
which should make it more obvious to the reader that the function is
contained within the current translation unit. Functions that were
not referenced were removed.
These symbols were identified by:
$ nm -A libvpx.a | sort -k3 | uniq -c -f2 | grep ' [A-Z] ' \
| sort | grep '^ *1 '
Change-Id: I59609f58ab65312012c047036ae1e0634f795779
Remove allocation/deallocation of stats storage.
Remove full search functions in machine specific encoder inits.
Remove last pass validation in validate_config.
Change-Id: I7f29be69273981a4fef6e80ecdb6217c68cbad4e
allow for optimized versions of apply_temporal_filter
(now vp8_apply_temporal_filter_c)
the function was previously declared as static and appears to have been
inlined. with this change, that's no longer possible. performance takes
a small hit.
the declaration for vp8_cx_temp_filter_c was moved to onyx_if.c because
of a circular dependency. for rtcd, temporal_filter.h holds the
definition for the rtcd table, so it needs to be included by onyx_int.h.
however, onyx_int.h holds the definition for VP8_COMP which is needed
for the function prototype. blah.
Change-Id: I499c055fdc652ac4659c21c5a55fe10ceb7e95e3
Use mpsadbw, and calculate 8 sad at once. Function list:
vp8_sad16x16x8_sse4
vp8_sad16x8x8_sse4
vp8_sad8x16x8_sse4
vp8_sad8x8x8_sse4
vp8_sad4x4x8_sse4
(test clip: tulip)
For best quality mode, this gave encoder a 5% performance boost.
For good quality mode with speed=1, this gave encoder a 3%
performance boost.
Change-Id: I083b5a39d39144f88dcbccbef95da6498e490134
This patch fixes the system dependent entries for the half-pixel
variance functions in both the RTCD and non-RTCD cases:
- The generic C versions of these functions are now correct.
Before all three cases called the hv code.
- Wire up the ARM functions in RTCD mode
- Created stubs for x86 to call the optimized subpixel functions
with the correct parameters, rather than falling back to C
code.
Change-Id: I1d937d074d929e0eb93aacb1232cc5e0ad1c6184
The primary goal is to allow a binary to be built which supports
NEON, but can fall back to non-NEON routines, since some Android
devices do not have NEON, even if they are otherwise ARMv7 (e.g.,
Tegra).
The configure-generated flags HAVE_ARMV7, etc., are used to decide
which versions of each function to build, and when
CONFIG_RUNTIME_CPU_DETECT is enabled, the correct version is chosen
at run time.
In order for this to work, the CFLAGS must be set to something
appropriate (e.g., without -mfpu=neon for ARMv7, and with
appropriate -march and -mcpu for even earlier configurations), or
the native C code will not be able to run.
The ASFLAGS must remain set for the most advanced instruction set
required at build time, since the ARM assembler will refuse to emit
them otherwise.
I have not attempted to make any changes to configure to do this
automatically.
Doing so will probably require the addition of new configure options.
Many of the hooks for RTCD on ARM were already there, but a lot of
the code had bit-rotted, and a good deal of the ARM-specific code
is not integrated into the RTCD structs at all.
I did not try to resolve the latter, merely to add the minimal amount
of protection around them to allow RTCD to work.
Those functions that were called based on an ifdef at the calling
site were expanded to check the RTCD flags at that site, but they
should be added to an RTCD struct somewhere in the future.
The functions invoked with global function pointers still are, but
these should be moved into an RTCD struct for thread safety (I
believe every platform currently supported has atomic pointer
stores, but this is not guaranteed).
The encoder's boolhuff functions did not even have _c and armv7
suffixes, and the correct version was resolved at link time.
The token packing functions did have appropriate suffixes, but the
version was selected with a define, with no associated RTCD struct.
However, for both of these, the only armv7 instruction they actually
used was rbit, and this was completely superfluous, so I reworked
them to avoid it.
The only non-ARMv4 instruction remaining in them is clz, which is
ARMv5 (not even ARMv5TE is required).
Considering that there are no ARM-specific configs which are not at
least ARMv5TE, I did not try to detect these at runtime, and simply
enable them for ARMv5 and above.
Finally, the NEON register saving code was completely non-reentrant,
since it saved the registers to a global, static variable.
I moved the storage for this onto the stack.
A single binary built with this code was tested on an ARM11 (ARMv6)
and a Cortex A8 (ARMv7 w/NEON), for both the encoder and decoder,
and produced identical output, while using the correct accelerated
functions on each.
I did not test on any earlier processors.
Change-Id: I45cbd63a614f4554c3b325c45d46c0806f009eaa
Changes 'The VP8 project' to 'The WebM project', for consistency
with other webmproject.org repositories.
Fixes issue #97.
Change-Id: I37c13ed5fbdb9d334ceef71c6350e9febed9bbba
The new fdct lowers the round trip sum squared error for a
4x4 block ~0.12. or ~0.008/pixel. For reference, the old
matrix multiply version has average round trip error 1.46
for a 4x4 block.
Thanks to "derf" for his suggestions and references.
Change-Id: I5559d1e81d333b319404ab16b336b739f87afc79
When the license headers were updated, they accidentally contained
trailing whitespace, so unfortunately we have to touch all the files
again.
Change-Id: I236c05fade06589e417179c0444cb39b09e4200d
