Coding and costing of mv reference signal.
Issues in updating MV ref with COMPANDED_MVREF_THRESH
to be resolved. Ideally the MV precision should be defined based
on absolute MV magnitude not as now the MV ref magnitude.
Update to mv counts moved into bitstream.c because otherwise
if the motion reference is changed at the last minute the encoder
and decoder get out of step in terms of the counts used to update
entropy probs.
Code working on a few test clips but no results yet re benefit vs
signaling cost and no tuning of red loop to test lower cost alternatives
based on the available reference values.
Patch 3. Added check to make sure we don't pick a reference
that would give rise to an uncodeable / out of range residual.
Patch 6-7: Attempt to rebase. OK to submit but best to leave flag off for now.
Patch 9. Remove print no longer needed.
Change-Id: I1938c2ffe41afe6d3cf6ccc0cb2c5d404809a712
Quickly modified the ssse3 sixtap filters to support eight taps. For the test
clip used, a 23+% boost in decoder performance was seen. We can
revisit later and improve further.
Change-Id: I5f59860459e80d6fa23e6cc0fd91296a969f5240
Refactor per-transform copy & paste into a common function
update_coef_probs_common() and read_coef_probs_common(). The dry-run and
bit-writing loops in the encoder are still obvious candidates to be made
common, but they start to diverge a bit in the next commit, so are left
as-is for now.
Change-Id: I896bd3f4a073a6296eab7e92463fef79d8c6c08c
On Ubuntu 12.04, we got the following warning message:
<command-line>:0:0: warning: "_FORTIFY_SOURCE" redefined
[enabled by default]
<built-in>:0:0: note: this is the location of the previous definition
This was already fixed in VP8 configure file. Did the same change in
experimental branch to stop this warning.
Change-Id: Id162e5fd8841585ae806df6560b2f7536ea307c0
There is a macro DEFAULT_INTERP_FILTER defined in encoder/onyx_if.c that
is set as EIGHTTAP for now - so SWITCHABLE is not really used. Ideally,
this should be SWITCHABLE but that would make the encoder quite a bit slower.
We will change the default filter to SWITCHABLE once we find a faster way to
search for switchable filters.
Change-Id: Iee91832cdc07e6e14108d9b543130fdd12fc9874
* changes:
Fix another typo in 4x4-transform-for-i8x8-intra-pred coeff contexts.
8x8 transform support in splitmv.
Use SPLITMV_PARTITIONING instead of a plain integer type.
For splitmv, where partitioning is 8x16, 16x8 or 8x8, this patch
uses the 8x8 transform (instead of the 4x4) if txfm_mode is
ALLOW_8X8 or ALLOW_16X16. For TX_MODE_SELECT, splitmv can indicate
which of the 2 transform sizes (4x4 or 8x8) it wants to use.
Gains (with hybridtx4x4/8x8/16x16 and tx_select experiments
enabled) on derf: +0.9%, HD: +0.4%, STD/HD: +0.8% (SSIM or overall
PSNR, both metrics show similar improvements).
Change-Id: Ide954b000b415548ed92a7ac78e24f36e60fcf06
This can be used to distinguish between 16x8, 8x16, 8x8 and 4x4
partitioning modes when choosing splitmv as a MB mode.
Change-Id: Idc8b59772e1a80ccc4ad44d63c5c2ec3fc061a3c
