Further simplification of mvref search to return
only the top two candidates. Distance weights removed
as the test order reflects distance anyway.
Change-Id: I0518cab7280258fec2058670add4f853fab7b855
As we are no longer able to sort the candidate
mvrefs in both encoder and decode and given
that the cost of explicit signalling has proved
prohibitive, it no longer makes sense to find more
than 2 candidates.
This patch:
Modifies and simplifies add_candidate_mv()
Removes the forced addition of a 0 vector in the
MAX_MV_REF_CANDIDATES-1 position (in preparation
to reducing MAX_MV_REF_CANDIDATES to 2).
Re-orders the addition of candidates slightly.
This actually gives small gains (circa 0.2% on std-hd)
A subsequent patch will remove NEW_MVREF experiment,
reduce MAX_MV_REF_CANDIDATES to 2 and remove distance
weights as these are implicit now in the order.
Change-Id: I3dbe1a6f8a1a18b3c108257069c22a1141a207a4
This patch adds column-based tiling. The idea is to make each tile
independently decodable (after reading the common frame header) and
also independendly encodable (minus within-frame cost adjustments in
the RD loop) to speed-up hardware & software en/decoders if they used
multi-threading. Column-based tiling has the added advantage (over
other tiling methods) that it minimizes realtime use-case latency,
since all threads can start encoding data as soon as the first SB-row
worth of data is available to the encoder.
There is some test code that does random tile ordering in the decoder,
to confirm that each tile is indeed independently decodable from other
tiles in the same frame. At tile edges, all contexts assume default
values (i.e. 0, 0 motion vector, no coefficients, DC intra4x4 mode),
and motion vector search and ordering do not cross tiles in the same
frame.
t log
Tile independence is not maintained between frames ATM, i.e. tile 0 of
frame 1 is free to use motion vectors that point into any tile of frame
0. We support 1 (i.e. no tiling), 2 or 4 column-tiles.
The loopfilter crosses tile boundaries. I discussed this briefly with Aki
and he says that's OK. An in-loop loopfilter would need to do some sync
between tile threads, but that shouldn't be a big issue.
Resuls: with tiling disabled, we go up slightly because of improved edge
use in the intra4x4 prediction. With 2 tiles, we lose about ~1% on derf,
~0.35% on HD and ~0.55% on STD/HD. With 4 tiles, we lose another ~1.5%
on derf ~0.77% on HD and ~0.85% on STD/HD. Most of this loss is
concentrated in the low-bitrate end of clips, and most of it is because
of the loss of edges at tile boundaries and the resulting loss of intra
predictors.
TODO:
- more tiles (perhaps allow row-based tiling also, and max. 8 tiles)?
- maybe optionally (for EC purposes), motion vectors themselves
should not cross tile edges, or we should emulate such borders as
if they were off-frame, to limit error propagation to within one
tile only. This doesn't have to be the default behaviour but could
be an optional bitstream flag.
Change-Id: I5951c3a0742a767b20bc9fb5af685d9892c2c96f
Adds an error-resilient mode where frames can be continued
to be decoded even when there are errors (due to network losses)
on a prior frame. Specifically, backward updates are turned off
and probabilities of various symbols are reset to defaults at
the beginning of each frame. Further, the last frame's mvs are
not used for the mv reference list, and the sorting of the
initial list based on search on previous frames is turned off
as well.
Also adds a test where an arbitrary set of frames are skipped
from decoding to simulate errors. The test verifies (1) that if
the error frames are droppable - i.e. frame buffer updates have
been turned off - there are no mismatch errors for the remaining
frames after the error frames; and (2) if the error-frames are non
droppable, there are not only no decoding errors but the mismatch
PSNR between the decoder's version of the post-error frames and the
encoder's version is at least 20 dB.
Change-Id: Ie6e2bcd436b1e8643270356d3a930e8989ff52a5
This experimental change reorders the search so
that all possible references that match the target
reference frame are tested first and these in order
of distance from the current block. These will usually
be the highest scoring candidates.
If we do not find enough good candidates this way
we try non matching cases. These will usually be lower
scoring candidates.
The change in order together with breakouts when
we have found enough candidates should reduce
the computational cost and especially reduce the number
of sort operations.
Quality Results:
Std Hd +0.228%, Hd +0.074%, YT +0.046%, derf +0.137%
This effect is probably due to the fact that more distant
weak candidates are now less likely to get "promoted" over
near candidates even if they are repeated.
Change-Id: Iec37e77d88a48ad0ee1f315b14327a95d63f81f6
This patch reduces the cpu cost of the MV ref
search by only allowing insert for candidates
that would be in the current top 4.
This could alter the outcome and slightly favors
near candidates which are tested first but also
limits the worst case loop count to 4 and means in
many cases it will drop out and not happen.
Change-Id: Idd795a825f9fd681f30f4fcd550c34c38939e113
This patch allows use of 8x8 and 4x4 ADST correctly for Intra
16x16 modes and Intra 8x8 modes when the block size selected
is smaller than the prediction mode. Also includes some cleanups
and refactoring.
Rebase.
Change-Id: Ie3257bdf07bdb9c6e9476915e3a80183c8fa005a
Support for gyp which doesn't support multiple objects in the same
static library having the same basename.
Change-Id: Ib947eefbaf68f8b177a796d23f875ccdfa6bc9dc
