Adds RD integration for 32x16, 16x32, 64x32 and 32x64 rectangular blocks.
Derf almost +0.6%, HD a little over +1.0%, STDHD +1.3%.
Change-Id: Id651fdb6a655fdbb5c47009757e63317acfb88a5
Enable recursive partition information coding from SB64X64 down to
MB16X16. The bit-stream syntax is now supporting rectangular block
sizes. It starts from SB64X64 and recursively describes the partition
type of the current block. If the partition type is PARTITION_NONE,
the block is coded as a single unit; if it is PARTITION_HORZ or
PARTITION_VERT, the block is segmented into two independently coded
rectangular units, with no further partition needed; otherwise, the
block is segmented into 4 square blocks. i.e., PARTITION_SPLIT case,
each can be potentially further partitioned.
Forward adaptive probability modeling is used for the partition
information coding, conditioned on the current block size.
Change-Id: I499365fb547839d555498e3bcc0387d8a3587d87
This function is now called from configures the ARNR
filter so it belongs with the other temporal filter
functions.
Change-Id: I64211875918364b5b8edfb97743e573c6def1663
Normalization of the frame boost value was being done
when it reached the value 1028. The intention was to
keep to a range of 10 bits, so it should have been
clipped above 1023.
Change-Id: I0afdddc1d2eb9e7822ec4578903cbe6ec0b33b91
This flag was added to VP8 to allow a mode where MB-level skipping
was not allowed, saving a bit per mb. It was never used in practice,
and hasn't been tested in VP9, so remove it.
Change-Id: Id450ec6904c6d06c1919508e7efc52d05cde5631
Static threshold results slightly up (+0.1% on derf), probably b/c
we now take the filter (sharp/lowpass) into account for the breakout
decision.
Change-Id: I9f597601da434205142afd05f32690e7ba8fd690
This is work-in-progress, it implements multiple ARF
encoding behind an experimental flag.
It adds the ability to insert multiple ARF frames into a
single ARF group. This patch implements the reordering
of the coded frames, and implements a fixed-length coding
pattern. It applies a fixed quantizer strategy based on
where the frame is in the coding sequence.
Further work to modify the rate control strategy is
ongoing and will be submitted via a set of future patches.
In this first step, each ARF group is recursively
bisected and an ARF frame added at that position in the
sequence. The recursion continues until ARF frames are
within MIN_GF_INTERVAL frames.
The code sits behind the "multiple-arf" experimental
flag ("CONFIG_MULTIPLE_ARF"). The experimental flag
"oneshotq" ("CONFIG_ONESHOTQ") also needs to be enabled
for this patch to work correctly.
Change-Id: Ie473b05ebb43ac473c0cfb659b2b8042823085e2
Combine superblock inter predictors into a unified function that
allows configurable block width and height. The inter predictions
of block sizes smaller than 16x16 are handled differently. To be
continued on merging them later.
Change-Id: I14075959dd5e221f00c205c99ca35c1c31ef728e
The probabilities derived from these statistics are used in bitstream
writing; therefore, we should only do this when we actually decide to
use macroblock coding (over superblock coding). Derf gains +0.15%.
Change-Id: I196814c070a7c79889590658ce10a6eb07454389
The intra predictor supports configurable block sizes. It can handle
intra prediction down to 4x4 sizes, when enabled in BLOCK_SIZE_TYPE.
Change-Id: I7399ec2512393aa98aadda9813ca0c83e19af854
Rename pick_mb_modes to pick_mb_mode, since it now handles only a
single macroblock. This is consistent with pick_sb_mode handling a
single non-macroblock.
Change-Id: I896fdfa06436b2d8c24d6474718cc74420df6b3b
This patch changes the default with the modecoefprob expt
to use mode-based forward updates with one-node pegged
modeling.
The maximum difference with fully trained tables is now
less that 0.1%.
Change-Id: I06b44322e10c6703f93f3c1d48d973b1136a0618
This patch will use the dest buffer instead of the
predictor buffer. This will allow us in future commits
to remove the extra mem copy that occurs in the dequant
functions when eob == 0. We should also be able to remove
extra params that are passed into the dequant functions.
Change-Id: I7241bc1ab797a430418b1f3a95b5476db7455f6a
