While CONFIG_INTERNAL_STATS=1, PSNR is calculated while encoding.
The aligned width/height were used mistakenly in the calculation.
This patch fixed it, and used the orignal image width/height.
Change-Id: Iad5334f8693af761b71ebb78f2587db8a3404ecf
Factor in segment#2 and skip blocks into the postencode estimated bits,
and increase somewhat the aggressiveness of the refresh.
PSNR/SSIM Metrics on RTC set go up by ~0.8/0.5%.
Change-Id: I5d4e7cb00a3aefb25d18c88b6b24118b72dc5d51
This commit makes the encoder to explicitly calculate the SAD
associated with the LAST_FRAME motion vector and compare it to
that of the GOLDEN_FRAME given by integral projection motion
estimation. It skips the expensive sub-pixel motion search over
GOLDEN_FRAME when the LAST_FRAME can provide fairly good motion
compensated prediction quality.
For dark720p speed -6 single thread goes from
33304 b/f, 40.070 dB, 18156 ms ->
33319 b/f, 40.061 dB, 17611 ms
Change-Id: I01bc94b9b598075567a392111046b97a9bc30efe
Because the call to vpx_codec_control at line 928 is now guarded by
!frame_parallel, 'corrupted' may not be set.
Change-Id: Id166bd8a8cdb5e5120fca1640011a3545f6e178a
Use force_split to constrain the partition selection.
This is used because in the top-down approach to variance partition,
a block size may be selected even though one of its subblocks may have
high variance.
In this patch the selection of the 64x64 block size will only
be allowed if the variance of all the 32x32 subblocks are also below the threshold.
Stil testing, but some visual improvement for areas near slow moving boundary
can be seen. Metrics for RTC set increase by about ~0.5%.
Change-Id: Iab3e7b19bf70f534236f7a43fd873895a2bb261d
Shut off all the metric checks for golden reference frame, if we
decide that it is unlikely to be selected for reference.
Change-Id: Ie457cc1fd43935584403b4982659aed80fb9909c
Move the scaling factor outside column projection. This avoids
repeated calculation of the same scaling factor. Profiling shows
that the percentage of vp9_int_pro_col_sse2 of overall cycles
goes from 2.29% down to 1.88%.
Change-Id: I5ac4e324ab2d7f33ba2de66dd2a12e04e04dfd66
1. remove duplicate initialization to mbmi->interp_filter.
2. move mv clamping into ref_frame loop instead of mode checking loop.
3. move the check if last frame is same as golden frame earlier to
avoid initialization of Golden reference related variables.
Change-Id: Idf2d05e19e94a24f69cc289687869fc71d2ff289
use \li to separate the list items contained in conditionals. this
avoids the encode page becoming a sub-item of decode; likely a problem
in <1.8.3.
+ fix encoder conditional, spelling error
+ correct encode page name to match decode 'Encoding'
Change-Id: I67890f52bed8e708bad63fb8819a074e0beff2ca
use \li to denote list items with \if.
fixes the following likely visible in <1.8.3:
usage.dox: warning: Invalid list item found
usage.dox: warning: End of list marker found without any preceding list items
Change-Id: I33c72799edf9f8866596ac8f79247050b8c75681
The compression performance of speed -5 is on average 12.6% better
than speed -6. At lower bit-rates, the gains are typically 20% or
more. For 2-thread encoding, the speed -5 takes about 1.6x time of
speed -6.
Change-Id: If7a73464a24d33e8f49b9533b51ec51c8da7fc80
