Replaced a divide by 9 with 8, so some very small difference,
but otherwise no change in behavior.
Change-Id: I1079ae3c41e0789ff0bc6fa9940a238b6bca0f5b
Simple skin detection, from vp8; works reasonable on most of the
RTC clips, but could miss sometimes.
Added debug flag to write out skin map over source input.
Change-Id: I2caea7592f1c459047aac46627eeb24a94946464
This commit allows the encoder to properly account for the mode
cost in sub8x8 non-RD mode decision.
Change-Id: I2951960d20e37ed08e372ee0c7044935b2b9b899
Add the rate cost on inter prediction filter type to the overall
rate-distortion cost in vp9_pick_mode_inter.
Change-Id: I72c34017adf5220cadb3962694ee5404469fc673
This commit adds a heuristic rate cost of reference frame to the
non-RD mode decision. It improves the compression performance of
speed -6 by 0.31% and speed -5 by 0.69%.
Change-Id: If7f3b45519d49b2cb640bcb7316a254efc8be446
This is to avoid redo the same calculation repeatly, and also allow
easier adjustments for further experiments.
This commit shall have no effect on quality/compression.
Change-Id: I4460acf5c808ff5518da18d21e002c5da58af857
Note: This feature is still in development.
Add an option for the encoder to decide the resolution
at which to encode each frame.
Each KF/GF/ARF goup is tested to see if it would be
better encoded at a lower resolution. At present, each
KF/GF/ARF is coded first at full-size and if the coded
size exceeds a threshold (twice target data rate) at
the maximum active Q then the entire group is encoded
at lower resolution.
This feature is enabled in vpxenc by setting:
--resize-allowed=1
In addition, if the vpxenc command line also specifies
valid frame dimensions using:
--resize-width=XXXX & --resize_height=YYYY
then *all* frames will be encoded at this resolution.
Change-Id: I13f341e0a82512f9e84e144e0f3b5aed8a65402b
This commit fixes the sub block partition size used in
fill_mode_info_sb. Previous implementation effectively disabled
the rectangular block sizes. This commit resolved this issue.
Change-Id: Ic1c383ab0a9a2e7d59e85b388093f1f1f94d1e7f
This commit makes the ZEROMV mode first in the search order to
ensure that the zero mv is always checked in the RTC coding mode.
It improves the average speed -6 compression performance by 0.3%
in both PSNR and SSIM at no visible speed change.
Change-Id: I465a7e59f4e20cd84fee3f02ced6f98036945949
The high bit depth build failed while building for 32bit target.
The bugs were in vp9_highbd_subpel_variance.asm and
vp9_highbd_sad4d_sse2.asm functions. This patch fixed the bugs,
and made 32bit build work.
Change-Id: Idc8e5e1b7965bb70d4afba140c6583c5d9666b75
On rtc set:
speed 7 quality improves about 0.5%
speed 8 quality improves about 1.0%
Encoding time for speed 7 changes from 67804ms to 65889ms
Encoding time for speed 8 changes from 58659ms to 56808ms
Change-Id: Iabcfb53012fc1b9f3326cdbc167e5758b8c7ad30
Reuse the yv12_mb array to fetch the buffer pointers/strides
corresponding to the current reference frame.
Change-Id: I5276b7494158b2cccef15213be2dc189e9036851
This commit allows the encoder to account for additional chroma
plane costs in the mode decision process, if the current block
potentially contains significant color change. It improves the
visual quality at very low bit-rates.
The compression performance of dark720p is improved by 12.39% in
speed 6. For jimred at 150 kbps, the PSNR of V component (red)
increased by 0.2 dB, at the expense of about 5% increase in
encoding time. Note that for sequences where the chroma components
are fairly consistent, the encoding time increase is negligible.
On average the rtc set compression performance is improved by
1.172% in PSNR and 1.920% in SSIM.
Change-Id: Ia55b24ef23a25304f7ec9958fbf07fd6e658505c
The original implementation had the following comment:
// Ignore mv costing if mvsadcost is NULL
However the current implementation does not allow for this.
If x exists then nmvsadcost must not be null.
This removes the only warning from -Wpointer-bool-conversion
https://code.google.com/p/webm/issues/detail?id=894
Change-Id: I1a2cee340d7972d41e1bbbe1ec8dfbe917667085
1. Adjusted the threshold for coef update computation based on counts
of tx used, avoid coef update computation when count is low (<20)
2. Move sf->lpf_pick = LPF_PICK_MINIMAL_LPF to speed 8.
Change-Id: I02b44309e40fcdbf135c7934ae067a3f42502d30
In frame parallel decode, libvpx decoder decodes several frames on all
cpus in parallel fashion. If not being flushed, it will only return frame
when all the cpus are busy. If getting flushed, it will return all the
frames in the decoder. Compare with current serial decode mode in which
libvpx decoder is idle between decode calls, libvpx decoder is busy
between decode calls.
Current frame parallel decode will only speed up the decoding for frame
parallel encoded videos. For non frame parallel encoded videos, frame
parallel decode is slower than serial decode due to lack of loopfilter
worker thread.
There are still some known issues that need to be addressed. For example:
decode frame parallel videos with segmentation enabled is not right sometimes.
* frame-parallel:
Add error handling for frame parallel decode and unit test for that.
Fix a bug in frame parallel decode and add a unit test for that.
Add two test vectors to test frame parallel decode.
Add key frame seeking to webmdec and webm_video_source.
Implement frame parallel decode for VP9.
Increase the thread test range to cover 5, 6, 7, 8 threads.
Fix a bug in adding frame parallel unit test.
Add VP9 frame-parallel unit test.
Manually pick "Make the api behavior conform to api spec." from master branch.
Move vp9_dec_build_inter_predictors_* to decoder folder.
Add segmentation map array for current and last frame segmentation.
Include the right header for VP9 worker thread.
Move vp9_thread.* to common.
ctrl_get_reference does not need user_priv.
Seperate the frame buffers from VP9 encoder/decoder structure.
Revert "Revert "Revert "Revert 3 patches from Hangyu to get Chrome to build:"""
Conflicts:
test/codec_factory.h
test/decode_test_driver.cc
test/decode_test_driver.h
test/invalid_file_test.cc
test/test-data.sha1
test/test.mk
test/test_vectors.cc
vp8/vp8_dx_iface.c
vp9/common/vp9_alloccommon.c
vp9/common/vp9_entropymode.c
vp9/common/vp9_loopfilter_thread.c
vp9/common/vp9_loopfilter_thread.h
vp9/common/vp9_mvref_common.c
vp9/common/vp9_onyxc_int.h
vp9/common/vp9_reconinter.c
vp9/decoder/vp9_decodeframe.c
vp9/decoder/vp9_decodeframe.h
vp9/decoder/vp9_decodemv.c
vp9/decoder/vp9_decoder.c
vp9/decoder/vp9_decoder.h
vp9/encoder/vp9_encoder.c
vp9/encoder/vp9_pickmode.c
vp9/encoder/vp9_rdopt.c
vp9/vp9_cx_iface.c
vp9/vp9_dx_iface.c
This reverts commit a18da9760a.
Change-Id: I361442ffec1586d036ea2e0ee97ce4f077585f02
