Two head files dct.h and dct_x86.h were removed in a previous commit,
this commit removed the build's dependency on the two files.
Change-Id: Idd33712470912d39d42f133dc30b710cab6fa832
Preparation for project restructuring.
Added vp9_ prefix on some function names that have global scope.
Added static declaration on some that dont.
Change-Id: If072f78b4300e8c17cfeed82c5d17b59946dcc5e
Previously, in evaluating reference motion vectors, MVs are always
rounded to integer pixel position and SADs are calculated. This
commit takes into account the subpixel portion of the mvs, and uses
bilinear interpolation to produce reference pixel values in subpixel
postions. In addition, SSE is used in place of SAD. Pixels used are
16x2 above and 2x16 to the left.
This commmit intends to test the potential of this line of work in
term of compression improvement, obviously, the change would increase
decoder complexity significantly.
Test results
std-hd: 1.738%(avg) 1.779%(glb), 1.663%(ssim)
derf: 0.472%(avg) 0.477%(glb), 0.418%(ssim)
Change-Id: I3ae1b098f6289df78891134d9a5e4bb2fde87a0b
Cleaned up some inconsistent references using both xd-> and
x->e_mbd. to access the same data structure in the same function.
Change-Id: Ieb496fa22bf1feec6aa7bc70b941ea4f16e0f8b5
Coding and costing of mv reference signal.
Issues in updating MV ref with COMPANDED_MVREF_THRESH
to be resolved. Ideally the MV precision should be defined based
on absolute MV magnitude not as now the MV ref magnitude.
Update to mv counts moved into bitstream.c because otherwise
if the motion reference is changed at the last minute the encoder
and decoder get out of step in terms of the counts used to update
entropy probs.
Code working on a few test clips but no results yet re benefit vs
signaling cost and no tuning of red loop to test lower cost alternatives
based on the available reference values.
Patch 3. Added check to make sure we don't pick a reference
that would give rise to an uncodeable / out of range residual.
Patch 6-7: Attempt to rebase. OK to submit but best to leave flag off for now.
Patch 9. Remove print no longer needed.
Change-Id: I1938c2ffe41afe6d3cf6ccc0cb2c5d404809a712
Quickly modified the ssse3 sixtap filters to support eight taps. For the test
clip used, a 23+% boost in decoder performance was seen. We can
revisit later and improve further.
Change-Id: I5f59860459e80d6fa23e6cc0fd91296a969f5240
Refactor per-transform copy & paste into a common function
update_coef_probs_common() and read_coef_probs_common(). The dry-run and
bit-writing loops in the encoder are still obvious candidates to be made
common, but they start to diverge a bit in the next commit, so are left
as-is for now.
Change-Id: I896bd3f4a073a6296eab7e92463fef79d8c6c08c
On Ubuntu 12.04, we got the following warning message:
<command-line>:0:0: warning: "_FORTIFY_SOURCE" redefined
[enabled by default]
<built-in>:0:0: note: this is the location of the previous definition
This was already fixed in VP8 configure file. Did the same change in
experimental branch to stop this warning.
Change-Id: Id162e5fd8841585ae806df6560b2f7536ea307c0
There is a macro DEFAULT_INTERP_FILTER defined in encoder/onyx_if.c that
is set as EIGHTTAP for now - so SWITCHABLE is not really used. Ideally,
this should be SWITCHABLE but that would make the encoder quite a bit slower.
We will change the default filter to SWITCHABLE once we find a faster way to
search for switchable filters.
Change-Id: Iee91832cdc07e6e14108d9b543130fdd12fc9874
