Do the test filtering in the existing backup frame buffer instead of
the original. Copy the original data into extra buffer before doing
the filtering. This way there is no need to restore the original
unfiltered frame at the end of level picking process.
This came up in some discussions with Johann. Thanks!
Change-Id: I495f4301d983854673276c34ec0ddf9a9d622122
The partial frame copy function used to copy an extra 8 lines above
and below. The partial frame filtering can only modify 3 pixel rows
above the partial frame. Reduce copy to bare minimum needed, which is
4 lines, so that partial filtering on copied frame is possible.
Define the "magic" fraction number for partial filtering in
loopfilter.h .
Change-Id: I4791ffc541b6884b12759a0d0714a8faf16147ec
During the _pick only the Y plane is examined. In addition, data beyond
the borders of the frame is not read.
Change-Id: Ic549adfca70fc6e0b55f8aab0efe81f0afac89f9
sharpness was not recalculated in vp8cx_pick_filter_level_fast
remove last_filter_type. all values are calculated, don't need to update
the lfi data when it changes.
always use cm->sharpness_level. the extra indirection was annoying.
don't track last frame_type or sharpness_level manually. frame type
only matters for motion search and sharpness_level is taken care of in
frame_init
move function declarations to their proper header
Change-Id: I7ef037bd4bf8cf5e37d2d36bd03b5e22a2ad91db
This patch collects the twopass specific memebers of VP8_COMP into a
dedicated struct. This is a first step towards isolating the two pass
rate control and aids readability by decorating these variables with
the 'twopass.' namespace. This makes it clear to the reader in what
contexts the variable will be valid, and is a hint that a section of
code might be a good candidate to move to firstpass.c in later
refactoring. There likely will be other rate control modes that need
their own specific data as well.
This notation is probably overly verbose in firstpass.c, so an
alternative would be to access this struct through a pointer like
'rc->' instead of 'cpi->firstpass.' in that file. Feel free to make
a review comment to that effect if you prefer.
Change-Id: I0ab8254647cb4b493a77c16b5d236d0d4a94ca4d
The primary goal is to allow a binary to be built which supports
NEON, but can fall back to non-NEON routines, since some Android
devices do not have NEON, even if they are otherwise ARMv7 (e.g.,
Tegra).
The configure-generated flags HAVE_ARMV7, etc., are used to decide
which versions of each function to build, and when
CONFIG_RUNTIME_CPU_DETECT is enabled, the correct version is chosen
at run time.
In order for this to work, the CFLAGS must be set to something
appropriate (e.g., without -mfpu=neon for ARMv7, and with
appropriate -march and -mcpu for even earlier configurations), or
the native C code will not be able to run.
The ASFLAGS must remain set for the most advanced instruction set
required at build time, since the ARM assembler will refuse to emit
them otherwise.
I have not attempted to make any changes to configure to do this
automatically.
Doing so will probably require the addition of new configure options.
Many of the hooks for RTCD on ARM were already there, but a lot of
the code had bit-rotted, and a good deal of the ARM-specific code
is not integrated into the RTCD structs at all.
I did not try to resolve the latter, merely to add the minimal amount
of protection around them to allow RTCD to work.
Those functions that were called based on an ifdef at the calling
site were expanded to check the RTCD flags at that site, but they
should be added to an RTCD struct somewhere in the future.
The functions invoked with global function pointers still are, but
these should be moved into an RTCD struct for thread safety (I
believe every platform currently supported has atomic pointer
stores, but this is not guaranteed).
The encoder's boolhuff functions did not even have _c and armv7
suffixes, and the correct version was resolved at link time.
The token packing functions did have appropriate suffixes, but the
version was selected with a define, with no associated RTCD struct.
However, for both of these, the only armv7 instruction they actually
used was rbit, and this was completely superfluous, so I reworked
them to avoid it.
The only non-ARMv4 instruction remaining in them is clz, which is
ARMv5 (not even ARMv5TE is required).
Considering that there are no ARM-specific configs which are not at
least ARMv5TE, I did not try to detect these at runtime, and simply
enable them for ARMv5 and above.
Finally, the NEON register saving code was completely non-reentrant,
since it saved the registers to a global, static variable.
I moved the storage for this onto the stack.
A single binary built with this code was tested on an ARM11 (ARMv6)
and a Cortex A8 (ARMv7 w/NEON), for both the encoder and decoder,
and produced identical output, while using the correct accelerated
functions on each.
I did not test on any earlier processors.
Change-Id: I45cbd63a614f4554c3b325c45d46c0806f009eaa
Changes 'The VP8 project' to 'The WebM project', for consistency
with other webmproject.org repositories.
Fixes issue #97.
Change-Id: I37c13ed5fbdb9d334ceef71c6350e9febed9bbba
When the license headers were updated, they accidentally contained
trailing whitespace, so unfortunately we have to touch all the files
again.
Change-Id: I236c05fade06589e417179c0444cb39b09e4200d
