Use the proper seg/mode/ref filter offsets when selecting the
frame loop filter level for fast mode (pick_filter_level_fast).
Change-Id: I2473e2131c800ad19755cb6211ad735fecfe2ac0
Interleaved loopfiltering with decode. For 1080p clips, up to 1%
performance gain. For 4k clips, up to 10% seen. This patch is required
for better "frame-based" multithreading.
Change-Id: Ic834cf32297cc04f27e8205652fb9f70cbe290db
After a key frame encoding, the frame type could change while
filtering is still going on. Pass the frame type as parameter to the
loopfilter function and don't read it from common storage.
vp8cx_set_alt_lf_level has to be done before packing the stream.
Currently alt_lf_level is not used so there hasn't been any visible
problem here.
Change-Id: Ia114162158cd833c2b16e3b89303cc9c91f19165
Local variable offsets are now consistent for the functions,
removed unused parameters, reworked the assembly to eliminate
stalls/instructions.
Change-Id: Iaa37668f8a9bb8754df435f6a51c3a08d547f879
The partial frame copy function used to copy an extra 8 lines above
and below. The partial frame filtering can only modify 3 pixel rows
above the partial frame. Reduce copy to bare minimum needed, which is
4 lines, so that partial filtering on copied frame is possible.
Define the "magic" fraction number for partial filtering in
loopfilter.h .
Change-Id: I4791ffc541b6884b12759a0d0714a8faf16147ec
sharpness was not recalculated in vp8cx_pick_filter_level_fast
remove last_filter_type. all values are calculated, don't need to update
the lfi data when it changes.
always use cm->sharpness_level. the extra indirection was annoying.
don't track last frame_type or sharpness_level manually. frame type
only matters for motion search and sharpness_level is taken care of in
frame_init
move function declarations to their proper header
Change-Id: I7ef037bd4bf8cf5e37d2d36bd03b5e22a2ad91db
Separate simple filter with reduced no. of parameters.
MB filter level picking based on precalculated table. Level table updated for
each frame. Inside and edge limits precalculated and updated just when
sharpness changes. HEV threshhold is constant.
ARM targets use scalars and others vectors.
Change works only with --target=generic-gnu
All other targets have to be updated!
Change-Id: I6b73aca6b525075b20129a371699b2561bd4d51c
the decision to run the regular or simple loopfilter is made outside the
function and managed with pointers
stop tracking the option in two places. use filter_type exclusively
Change-Id: I39d7b5d1352885efc632c0a94aaf56b72cc2fe15
The dc_diff flag is used to skip loopfiltering. Instead
of setting this flag in the decoder/encoder, we now check
for this condition in the loopfilter.
Change-Id: Ie2b9cdf9e0f4e8b932bbd36e0878c05bffd28931
This eliminates a large set of warnings exposed by the Mozilla build
system (Use of C++ comments in ISO C90 source, commas at the end of
enum lists, a couple incomplete initializers, and signed/unsigned
comparisons).
It also eliminates many (but not all) of the warnings expose by newer
GCC versions and _FORTIFY_SOURCE (e.g., calling fread and fwrite
without checking the return values).
There are a few spurious warnings left on my system:
../vp8/encoder/encodemb.c:274:9: warning: 'sz' may be used
uninitialized in this function
gcc seems to be unable to figure out that the value shortcut doesn't
change between the two if blocks that test it here.
../vp8/encoder/onyx_if.c:5314:5: warning: comparison of unsigned
expression >= 0 is always true
../vp8/encoder/onyx_if.c:5319:5: warning: comparison of unsigned
expression >= 0 is always true
This is true, so far as it goes, but it's comparing against an enum, and the C
standard does not mandate that enums be unsigned, so the checks can't be
removed.
Change-Id: Iaf689ae3e3d0ddc5ade00faa474debe73b8d3395
Changes 'The VP8 project' to 'The WebM project', for consistency
with other webmproject.org repositories.
Fixes issue #97.
Change-Id: I37c13ed5fbdb9d334ceef71c6350e9febed9bbba
When the license headers were updated, they accidentally contained
trailing whitespace, so unfortunately we have to touch all the files
again.
Change-Id: I236c05fade06589e417179c0444cb39b09e4200d
