Various refactoring to make the subpel motion compensation
filters switchable by a frame level field.
Two types of 8-tap filters are supported in addition to the existing
bilinar and sixtap filters. One is the default 8-tap and the
other has a sharper cut-off for use with frames with substantial
edge content.
Patch 2: Added a preliminary strategy for filter selection based on
edginess detecton. Also includes some filter changes.
Change-Id: I866085bda5ae143cfdf2ec88157feaabdf7bd63a
This is the first patch for refactoring of the code related to
high-precision mv, so that 1/4 and 1/8 pel motion vectors can
co-exist in the same bit-stream by use of a frame level flag.
The current patch works fine for only use of 1/4th and
only use of 1/8th pel mv, but there are some issues with the
mode switching in between. Subsequent patches on this change Id
will fix the remaining issues.
Patch 2: Adds fixes to make sure that multiple mv precisions can
co-exist in the bit-stream. Frame level switching has been tested
to work correctly.
Patch 3: Fixes lines exceeding 80 char
Patch 4:
http://www.corp.google.com/~debargha/vp8_results/enhinterp.html
Results on derf after ssse3 bugfix, compared to everything
enabled but the 8-tap, 1/8-subpel and 1/16-subpel uv. Overall the
gains are about 3% now. Hopefully there are no more bugs lingering.
Apparently the sse3 bug affected the quartel subpel results more than
the eighth pel ones (which is understandabale because one bad predictor
due to the bug, matters less if there are a lot more subpel options
available as in the 1/8 subpel case).
The results in the 4th column correspond to the current settings.
The first two columns correspond to two settings of adaptive switching
of the 1/4 or 1/8 subpel mode based on initial Q estimate. These
do not work as good as just using 1/8 all the time yet.
Change-Id: I3ef392ad338329f4d68a85257a49f2b14f3af472
The Lagrangian interpolation filter is maximally flat in the
passband. There is non-trivial improvement with the hd set, while
for derf the results are virtually unchanged.
See:
http://www.corp.google.com/~debargha/vp8_results/enhinterpn.html (derf)
http://www.corp.google.com/~debargha/vp8_results/enhinterpn_hd.html (HD)
Patch 2: Updated the results for derf in the html above to use the
new baseline. There is still about 4% improvement. Will update the
hd baseline later (since it takes 9 hours to run on my machine)
Patch 3: By mistake the default filter was left at 60 - should be 0
to use the new interpolation filter.
Change-Id: If5f64444976562415d68a2aeabb94fdfa0d47890
* Removes EDGE_PIXEL_FILTER for external sanpshot
* changes the default 8-tap filter based on high precision results
in http://www.corp.google.com/~debargha/vp8_results/enhinterpn.html
* changes the default prob tables for high-precision mv encoding to
favor zeros in the last bit (i.e. quarter pel). This is only important
for short clips.
Change-Id: I02bb0de8679d9eec06cdbcc8160dbf073cd847a4
This is the initial patch for supporting 1/8th pel
motion. Currently if we configure with enable-high-precision-mv,
all motion vectors would default to 1/8 pel. Encode and
decode syncs fine with the current code. In the next phase
the code will be refactored so that we can choose the 1/8
pel mode adaptively at a frame/segment/mb level.
Derf results:
http://www.corp.google.com/~debargha/vp8_results/enhinterp_hpmv.html
(about 0.83% better than 8-tap interpoaltion)
Patch 3: Rebased. Also adding 1/16th pel interpolation for U and V
Patch 4: HD results.
http://www.corp.google.com/~debargha/vp8_results/enhinterp_hd_hpmv.html
Seems impressive (unless I am doing something wrong).
Patch 5: Added mmx/sse for bilateral filtering, as well as enforced
use of c-versions of subpel filters with 8-taps and 1/16th pel;
Also redesigned the 8-tap filters to reduce the cut-off in order to
introduce a denoising effect. There is a new configure option
sixteenth-subpel-uv which will use 1/16 th pel interpolation for
uv, if the motion vectors have 1/8 pel accuracy.
With the fixes the results are promising on the derf set. The enhanced
interpolation option with 8-taps alone gives 3% improvement over thei
derf set:
http://www.corp.google.com/~debargha/vp8_results/enhinterpn.html
Results on high precision mv and on the hd set are to follow.
Patch 6: Adding a missing condition for CONFIG_SIXTEENTH_SUBPEL_UV in
vp8/common/x86/x86_systemdependent.c
Patch 7: Cleaning up various debug messages.
Patch 8: Merge conflict
Change-Id: I5b1d844457aefd7414a9e4e0e06c6ed38fd8cc04
using an 8-tap filter.
The results with 3 different 8-tap filters on the derf set are in:
http://www.corp.google.com/~debargha/vp8_results/enhinterp.html
The one that gives the most gain achieves an overall gain of about
0.6%. The results for a set of 12 hd (720p) videos are in:
http://www.corp.google.com/~debargha/vp8_results/enhinterp_hd.html
with max gain of 0.55% with the same filter. The best filter apparently
achieves the best trade-off between pass band ripple and stop band
attenuation.
Change-Id: I919e28ae245c0493147fa0864f8c9d048a9dd530
This patch introduces the concept of dual inter16x16 prediction. A
16x16 inter-predicted macroblock can use 2 references instead of 1,
where both references use the same mvmode (new, near/est, zero). In the
case of newmv, this means that two MVs are coded instead of one. The
frame can be encoded in 3 ways: all MBs single-prediction, all MBs dual
prediction, or per-MB single/dual prediction selection ("hybrid"), in
which case a single bit is coded per-MB to indicate whether the MB uses
single or dual inter prediction.
In the future, we can (maybe?) get further gains by mixing this with
Adrian's 32x32 work, per-segment dual prediction settings, or adding
support for dual splitmv/8x8mv inter prediction.
Gain (on derf-set, CQ mode) is ~2.8% (SSIM) or ~3.6% (glb PSNR). Most
gain is at medium/high bitrates, but there's minor gains at low bitrates
also. Output was confirmed to match between encoder and decoder.
Note for optimization people: this patch introduces a 2nd version of
16x16/8x8 sixtap/bilin functions, which does an avg instead of a
store. They may want to look and make sure this is implemented to
their satisfaction so we can optimize it best in the future.
Change-ID: I59dc84b07cbb3ccf073ac0f756d03d294cb19281
A large number of functions were defined with external linkage, even
though they were only used from within one file. This patch changes
their linkage to static and removes the vp8_ prefix from their names,
which should make it more obvious to the reader that the function is
contained within the current translation unit. Functions that were
not referenced were removed.
These symbols were identified by:
$ nm -A libvpx.a | sort -k3 | uniq -c -f2 | grep ' [A-Z] ' \
| sort | grep '^ *1 '
Change-Id: I59609f58ab65312012c047036ae1e0634f795779
make reference version of bilinear_filters short.
use reference versions of bilinear_filters and sub_pel_filters when
possible.
recognize that Width was being passed into
filter_block2d_bil_first_pass multiple times. ARM version had already
fixed this. propegate to C.
change references to src_pixels_per_line to src_pitch and standardize on
src/dst (instead of input/output).
recognize that first_pass is only run in the verticle and second_pass
only horizontal. ARM version had already fixed this. propegate to C
Change-Id: I292d376d239a9a7ca37ec2bf03cc0720606983e2
