When running multi-layer (ML) encodes and dynamically
changing coding parameters on the fly (e.g. frame
duration/rate, bandwidths allocated to each layer)
the encoder would not produce sensible output.
In certain cases the rate targeting would be
hideously inaccurate.
These fixes make it possible to change these coding
parameters correctly and to maintain accurate control
of the rate targeting.
I also added the specification of the input timebase
into the test program, vp8_scalable_patterns.c.
Patch 2: Moved declaration to appease MS compiler)
Change-Id: Ic8bb5a16daa924bb64974e740696e040d07ae363
The example encoder down-samples the input video frames a number of
times with a down-sampling factor, and then encodes and outputs
bitstreams with different resolutions.
Support arbitrary down-sampling factor, and down-sampling factor
can be different for each encoding level.
For example, the encoder can be tested as follows.
1. Configure with multi-resolution encoding enabled:
../libvpx/configure --target=x86-linux-gcc --disable-codecs
--enable-vp8 --enable-runtime_cpu_detect --enable-debug
--disable-install-docs --enable-error-concealment
--enable-multi-res-encoding
2. Run make
3. Encode:
If input video is 1280x720, run:
./vp8_multi_resolution_encoder 1280 720 input.yuv 1.ivf 2.ivf 3.ivf 1
(output: 1.ivf(1280x720); 2.ivf(640x360); 3.ivf(320x180).
The last parameter is set to 1/0 to show/not show PSNR.)
4. Decode:
./simple_decoder 1.ivf 1.yuv
./simple_decoder 2.ivf 2.yuv
./simple_decoder 3.ivf 3.yuv
5. View video:
mplayer 1.yuv -demuxer rawvideo -rawvideo w=1280:h=720 -loop 0 -fps 30
mplayer 2.yuv -demuxer rawvideo -rawvideo w=640:h=360 -loop 0 -fps 30
mplayer 3.yuv -demuxer rawvideo -rawvideo w=320:h=180 -loop 0 -fps 30
The encoding parameters can be modified in vp8_multi_resolution_encoder.c,
for example, target bitrate, frame rate...
Modified API. John helped a lot with that. Thanks!
Change-Id: I03be9a51167eddf94399f92d269599fb3f3d54f5
The calculated frame_rate is a state variable in the codec, and
shouldn't be maintained in the configuration struct. Move it to the
main part of cpi so that it isn't clobbered when the configuration
struct is updated. The initial framerate estimate is moved from the
vp8_cx_iface.c wrapper into the body of init_config() in onyx_if.c, so
that it is only called once and not reset on every call to
vp8_change_config().
Change-Id: I8d9a3d1283330d1ee297d07e9d78d1f2875f2465
check to make sure that cx_data buffer has enough room before
writting to it, prior behavior did not which could result in a crash.
Change-Id: I3fab6f2bc4a96d7c675ea81acd39ece121738b28
Added the ability to create rate-targeted, temporally
scalable, VP8 compatible bitstreams.
The application vp8_scalable_patterns.c demonstrates how
to use this capability. Users can create output bitstreams
containing upto 5 temporally separable streams encoded
as a single VP8 bitstream.
(previously abandoned as:
I92d1483e887adb274d07ce9e567e4d0314881b0a)
Change-Id: I156250a3fe930be57c069d508c41b6a7a4ea8d6a
buffer_level in VP8_COMP and starting_buffer_level, optimal_buffer_level
and maximum_buffer_size in VP8_CONFIG changed from int to int64_t
to avoid potential crash issues for larger target bit rates.
Change-Id: I0d5ab6c8a44c2fef51f30cd8df4bb4b739c5df26
Adding support in the encoder for generating
independent residual partitions by forcing
equal probabilities over the prev coef entropy
contexts.
Change-Id: I402f5c353255f3ca20eae2620af739f6a498cd21
This patch changes the rc_undershoot_pct and rc_overshoot_pct controls
to set the "aggressiveness" of rate adaptation, by limiting the
amount of difference between the target buffer level and the actual
buffer level which is applied to the target frame rate for this frame.
This patch was initially provided by arosenberg at logitech.com as
an attachment to issue #270. It was modified to separate these controls
from the other unrelated modifications in that patch, as well as to
use the pre-existing variables rather than introducing new ones.
Change-Id: Id542e3f5667dd92d857d5eabf29878f2fd730a62
The merge includes hooks to for CQ mode and other code
changes merged from the test branch.
CQ mode attempts to maintain a more stable quantizer within a clip
whilst also trying to adhere to a guidline maximum bitrate.
The existing target data rate parameter is used to specify the
guideline maximum bitrate.
A new parameter allows the user to specify a target CQ level.
For normal (non kf/gf/arf) frames, the quantizer will not drop BELOW the
user specified value (0-63). However, in some cases the encoder may
choose to impose a target CQ that is above that specified by the user,
if it estimates that consistent use of the target value is not compatible
with guideline maximum bitrate.
Change-Id: I2221f9eecae8cc3c431d36caf83503941b25e4c1
Add a new encoder control, VP8E_SET_TUNING, to allow the application
to inform the encoder that the material will benefit from certain
tuning. Expose this control as the --tune option to vpxenc. The args
helper is expanded to support enumerated arguments by name or value.
Two tunings are provided by this patch, PSNR (default) and SSIM.
Activity masking is made dependent on setting --tune=ssim, as the
current implementation hurts speed (10%) and PSNR (2.7% avg,
10% peak) too much for it to be a default yet.
Change-Id: I110d969381c4805347ff5a0ffaf1a14ca1965257
Debugging in postproc needs more flags to allow for specific
block types to be turned on or off in the visualizations.
Must be enabled with --enable-postproc-visualizer during
configuration time.
Change-Id: Ia74f357ddc3ad4fb8082afd3a64f62384e4fcb2d
Changes 'The VP8 project' to 'The WebM project', for consistency
with other webmproject.org repositories.
Fixes issue #97.
Change-Id: I37c13ed5fbdb9d334ceef71c6350e9febed9bbba
When the license headers were updated, they accidentally contained
trailing whitespace, so unfortunately we have to touch all the files
again.
Change-Id: I236c05fade06589e417179c0444cb39b09e4200d
This renames the vpx_codec/ directory to vpx/, to allow applications
to more consistently reference these includes with the vpx/ prefix.
This allows the includes to be installed in /usr/local/include/vpx
rather than polluting the system includes directory with an
excessive number of includes.
Change-Id: I7b0652a20543d93f38f421c60b0bbccde4d61b4f
