Deallocating the buffers before re-allocating them.
The fix passed James Berry's test program for memory
leak check.
Change-Id: I18c3cf665412c0e313a523e3d435106c03ca438d
Moved the code from the segmentation loop into a function
which is now called for each segment. This will allow us
to change the segment order checking more easily.
Change-Id: I9510d26f0acae5a73043fcca8f1984b121d3e052
When auto_golden wasn't set it forced all frames to be a golden
frame. Now the manual configured frequency is adhered to.
Change-Id: I360acac9bc487db0d9c4d4da6ee41f70c227c539
The inter_minq table controls the range of quantizers available
for a particular frame in two pass relative to a max Q value.
The changes reduces the range somewhat. The effect of this
was a small increase (0.3% average) in psnr for the test set
but it should also help encode speed somewhat for higher
quality modes as it will reduce the number of iterations in the
recode loop.
The change damps the range of quantizers available locally
within a section of a clip and should therefore help keep quality
more uniform. If there is systematic overshoot or undershoot the
range can shift gradually to accommodate. However, there is
some increased risk of overshoot or undershoot against the target
bit rate in VBR mode and this risk will be more pronounced for short
clips.
The change damps the range of quantizers available locally
within a section of a clip and should therefore help keep quality
more uniform. If there is systematic overshoot or undershoot the
range can shift gradually to accommodate. However, there is
some increased risk of overshoot or undershoot against the
target bit rate in VBR mode and this risk will be more
pronounced for short clips.
Change-Id: I84465567d49ae767c6c73ff2a2aac30c895adb52
Add vp8_mv_pred() to better predict starting MV for NEWMV
mode in vp8_rd_pick_inter_mode(). Set different search
ranges according to MV prediction accuracy, which improves
encoder performance without hurting the quality. Also,
as Yaowu suggested, using diamond search result as full
search starting point and therefore adjusting(reducing)
full search range helps the performance.
Change-Id: Ie4a3c8df87e697c1f4f6e2ddb693766bba1b77b6
On a keyframe alt ref and golden are refreshed. The flag was
not being set and so on the frame after a keyframe, motion
search would occur on the alt ref frame. This is not necessary
because the alt ref frame identical to the last frame in this
scenario.
Handle corner case where a forward alt-ref frame is put
directly after a keyframe.
Change-Id: I9be4cf290d694f8cf2f9a31852014b5ccf1504d3
remove warning comment in vpxenc.c: in case of 1x1 picture,
detect_bytes will be equal to '3' and we'll fall back to
RAW_TYPE.
fix read_frame() by tracking the pre-read buffer length
in the struct detect
Change-Id: If1ed86ee5260dcdbc8f9d10da6cbb84a4cc2f151
The sz member of the vpx_codec_stream_info_t structure must be
initialized when passed to vpx_codec_peek_stream_info().
Change-Id: I2d13d287d9639262b932cf44671a595fdf3c38ef
The baseline bits per MB prediction tables have been
re calibrated based on the assumption that bits per mb
is inversely proportional to the quantizer level.
Change-Id: Ibd355c7acac4b8053dda1baf1032fe35f11da7f7
Replaced existing code to decide if a frame recode is required
with a function call. This is to simplify addition of extra clauses
that may be needed for the planned constrained quality mode.
Also fixed a bug where by alt ref not considered in the test.
Change-Id: I3d40bb21abe3e19f8456761e6849deb171738b60
The example for disabling the active map used a hard-coded 320x240
resolution, rather than using what was passed on the command line.
Fixes#218
Change-Id: I3aed713e8aa7fcbf18dfbffd57f142b5cd9ee492
This function was never called in a context expecting a return value,
the return value was always a constant, and the !CONFIG_MULTITHREAD
path didn't have a return statement, which caused a compiler warning.
This patch changes the function to return void instead.
Fixes issue #231
Change-Id: I9ef7f56e54418b7265026c54fc4ed5660c1418d1
The ERROR macro collides wiith the MS SDK on Windows. Since we're not
making any win32 calls in this function, just #undef it first to take
ownership.
Change-Id: Ic18c60dfa3a33c52e6c49d3f4f8d3e7e3ac3341d
Adds native build configuration for Snow Leopard. Useful when
users configure without arguments on OSX 10.6.
Change-Id: I0bd63912a25bbfb9d4c8d58a781d0f390792429c
x86-64 passes arguments in registers. There is no need to push
them to the stack before using them.
This fixes 15acc84f10 where ebx
was not getting preserved on x86.
Change-Id: I1214b5f818a0201f75ab6ad7d5c6f448e09b16c2
The use of incorrect mv costing tables in the ARNR sub-pel
filtering code led to corruption of the altref buffer in some cases,
particularly at low data rates.
The average gain from this fix is about 0.3% but there are a few
extreme cases where nasty and visible artifacts manifested and
for these few data points the improvement is > 10%.
PGW and AWG
Change-Id: I95cc02b196a433e71d0d2bd2b933fe68ed31e796
When the first pts equaled 0 ivfenc was incorrectly increasing the
pts by 1. I changed the pts and last pts to be signed. I also set
the default value of last pts to -1.
Change-Id: I30bcec5af9b16d93fa9e3abbea7764b133e9cd73
This intends to correct the tendency that VP8 aggressively favors rate
on intra coded frames. Experiments tested different numbers in [0, 1]
and found 9/16 overall provided about 2-4% gains for all-intra coded
clips based on vpx-ssim metric. The impact on regular encoded clips
is much smaller but positive overall. Overall impact on psnr is also
positive even though very small.
Change-Id: If808553aaaa87fdd44691f9787820ac9856d9f8a
The fast quantizer assembly code has not been updated to match the new
exact quantizer, which was made the default in commit 6adbe09.
Specifically, they are not aware of the potential for the coefficient
to be scaled, which results in the quantized result exceeding the range
of the DCT. This patch restores the previous behavior of using the
non-shifted coefficients when in the fast quantizer code path, but
unfortunately requires rebuilding the tables when switching between the
two.
Change-Id: I0a33f5b3850335011a06906f49fafed54dda9546
Check to see if postproc was enabled when enabling the
postproc visualizer was wrong.
Fix for bug introduced in Change Ia74f357d
Change-Id: I4bee9ad2caee3cfe3bac6972047f6af7c54cad4e
Debugging in postproc needs more flags to allow for specific
block types to be turned on or off in the visualizations.
Must be enabled with --enable-postproc-visualizer during
configuration time.
Change-Id: Ia74f357ddc3ad4fb8082afd3a64f62384e4fcb2d
VBR rate control can become very noisy for the last few frames.
If there are a few bits to spare or a small overshoot then the
target rate and hence quantizer may start to fluctuate wildly.
This patch prevents further adjustment of the active Q limits for
the last few frames.
Patch also removes some redundant variables and makes one small bug fix.
Change-Id: Ic167831bec79acc9f0d7e4698bcc4bb188840c45
Small changes to the default zero bin and rounding tables.
Though the tables are currently the same for the Y1 and Y2 cases
I have left them as separate tables in case we want to tune this later.
There is now some adjustment of the zbin based on the prediction mode.
Previously this was restricted to an adjustment for gf/arf 0,0 MV.
The exact quantizer now marginal outperforms and is the default.
The overall average gain is about 0.5%
Change-Id: I5e4353f3d5326dde4e86823684b236a1e9ea7f47
The check '(user_data_end - partition < partition_size)' must be
evaluated as a signed comparison, but because partition_size was
unsigned, the LHS was promoted to unsigned, causing an incorrect
result on 32-bit. Instead, check the upper and lower bounds of
the segment separately.
Change-Id: I6266aba7fd7de084268712a3d2a81424ead7aa06
Change Ice204e86 identified a problem with bitrate undershoot due to
low precision in the timestamps passed to the library. This patch
takes a different approach by calculating the duration of this frame
and passing it to the library, rather than using a fixed duration
and letting the library average it out with higher precision
timestamps. This part of the fix only applies to vpxenc.
This patch also attempts to fix the problem for generic applications
that may have made the same mistake vpxenc did. Instead of
calculating this frame's duration by the difference of this frame's
and the last frame's start time, we use the end times instead. This
allows the framerate calculation to scavenge "unclaimed" time from
the last frame. For instance:
start | end | calculated duration
======+=======+====================
0ms 33ms 33ms
33ms 66ms 33ms
66ms 99ms 33ms
100ms 133ms 34ms
Change-Id: I92be4b3518e0bd530e97f90e69e75330a4c413fc
If this function fails silently, the nestegg context is destroyed and
future nestegg calls will segfault.
Change-Id: Ie6a0ea284ab9ddfa97b1843ef8030a953937c8cd
