The baseline bits per MB prediction tables have been
re calibrated based on the assumption that bits per mb
is inversely proportional to the quantizer level.
Change-Id: Ibd355c7acac4b8053dda1baf1032fe35f11da7f7
In the process of developing new intra prediction modes, tests have
shown removal of the low pass filtering from B_HE_PRED and B_VE_PRED
has an overall minor positive impact in both PSNR and SSIM metric.
Overall difference is about 0.1%. The change shall also have a small
positive impact on speed. Intuitively, this change should also reduce
some of the tendency of "flattening"
Change-Id: I3c43b0daca833c6eff77d00f19c811f9ef9368a3
Changing the MAX_PSNR to 100 to allow testing of further experiments
on extending quantizer range to near lossless. With an effective
quantizer of 1, encoder achieves ~68DB, which is consistent with
fdct/idct round trip error.
Change-Id: I7b6d0e94a8936968ef42e82e63ebb13999c36832
Extending the value range of tokens allows further experiments on
extending quantizer range. Encoder and decoder were verified to
produce matching reconstructed buffers by tests with forced
quantized value of 1.
Change-Id: I12faf92832867870b6f71ddeafbf643f1040086d
Replaced existing code to decide if a frame recode is required
with a function call. This is to simplify addition of extra clauses
that may be needed for the planned constrained quality mode.
Also fixed a bug where by alt ref not considered in the test.
Change-Id: I3d40bb21abe3e19f8456761e6849deb171738b60
x86-64 passes arguments in registers. There is no need to push
them to the stack before using them.
This fixes 15acc84f10 where ebx
was not getting preserved on x86.
Change-Id: I1214b5f818a0201f75ab6ad7d5c6f448e09b16c2
The use of incorrect mv costing tables in the ARNR sub-pel
filtering code led to corruption of the altref buffer in some cases,
particularly at low data rates.
The average gain from this fix is about 0.3% but there are a few
extreme cases where nasty and visible artifacts manifested and
for these few data points the improvement is > 10%.
PGW and AWG
Change-Id: I95cc02b196a433e71d0d2bd2b933fe68ed31e796
This intends to correct the tendency that VP8 aggressively favors rate
on intra coded frames. Experiments tested different numbers in [0, 1]
and found 9/16 overall provided about 2-4% gains for all-intra coded
clips based on vpx-ssim metric. The impact on regular encoded clips
is much smaller but positive overall. Overall impact on psnr is also
positive even though very small.
Change-Id: If808553aaaa87fdd44691f9787820ac9856d9f8a
The fast quantizer assembly code has not been updated to match the new
exact quantizer, which was made the default in commit 6adbe09.
Specifically, they are not aware of the potential for the coefficient
to be scaled, which results in the quantized result exceeding the range
of the DCT. This patch restores the previous behavior of using the
non-shifted coefficients when in the fast quantizer code path, but
unfortunately requires rebuilding the tables when switching between the
two.
Change-Id: I0a33f5b3850335011a06906f49fafed54dda9546
- Used three probability approach for temporal context as follows:
P0 - probability of no change if both above and left not changed
P1 - probability of no change if one of above and left has changed
P2 - probability of no change if both above and left have changed
In addition, a 1 bit/frame has been used to decide whether to use temporal context or to encode directly. The cost of using both the schemes is calculated ahead and the temporal_update flag is set if the cost of using temporal context is lower than encoding the segment ids directly.
This approach has given around 20% reduction in cost of bits needed to encode segmentation ids.
Change-Id: I44a5509599eded215ae5be9554314280d3d35405
Debugging in postproc needs more flags to allow for specific
block types to be turned on or off in the visualizations.
Must be enabled with --enable-postproc-visualizer during
configuration time.
Change-Id: Ia74f357ddc3ad4fb8082afd3a64f62384e4fcb2d
VBR rate control can become very noisy for the last few frames.
If there are a few bits to spare or a small overshoot then the
target rate and hence quantizer may start to fluctuate wildly.
This patch prevents further adjustment of the active Q limits for
the last few frames.
Patch also removes some redundant variables and makes one small bug fix.
Change-Id: Ic167831bec79acc9f0d7e4698bcc4bb188840c45
Small changes to the default zero bin and rounding tables.
Though the tables are currently the same for the Y1 and Y2 cases
I have left them as separate tables in case we want to tune this later.
There is now some adjustment of the zbin based on the prediction mode.
Previously this was restricted to an adjustment for gf/arf 0,0 MV.
The exact quantizer now marginal outperforms and is the default.
The overall average gain is about 0.5%
Change-Id: I5e4353f3d5326dde4e86823684b236a1e9ea7f47
