The CQ level was not using the q_trans[] array to convert
to a 0-127 range as per min and maxq
Experimental change to try and match the reconstruction
error for forced key frames approximately to that of the
previous frame by means of the recode loop. Though this
may cause extra recodes and the recode behavior has not
been optimized, it can only happen on forced key frames.
Change-Id: I1f7e42d526f1b1cb556dd461eff1a692bd1b5b2f
Previously when a frame was being overlaid on a previously coded
alt ref frame we only checked the alt ref 0,0 mode. Where there is
a possibility that the alt ref buffer is a filtered frame we should allow
the other prediction modes as normal or at the least allow use of
the last frame buffer.
Change-Id: I4d6227223d125c96b4f3066ec6ec9484fee7768c
In cases where the frame width is not a multiple of 16 the
ARNR filter would go wrong.
In vp8_temporal_filter_iterate_c when updating pointers
at the end of a row of MBs, the image size was
incorrectly used rather than using Num_MBs_In_Row
times 16 (Y) or 8 (U,V).
This worked when width is multiple of 16 but failed
otherwise.
Change-Id: I008919062715bd3d17c7aa2562ab58d1cb37053a
This change is designed to try and reduce pulsing effects when moving
with a complex transition like a fade, into an easy or static section in
an otherwise difficult clip in CQ mode.
The active CQ level is relaxed down to the user entered level for frames that
are generating less than the passed in minimum bandwidth.
Change-Id: Id6d8b551daad4f489c087bd742bc95418a95f3f0
Fixed discrepancy cpi->ni_frames vs cm->current_video_frame > 150.
Make one pass path explicit.
There is still scope for some odd behaviour around the transition
point at cpi->ni_frames > 150.
Change-Id: Icdee130fe6e2a832206d30e45bf65963edd7a74d
Where a key frame occurs because of a minimum interval
selected by the user, then these forced key frames ideally need
to be more closely matched in quality to the surrounding frame.
Change-Id: Ia55b1f047e77dc7fbd78379c45869554f25b3df7
Add a flag to always enable block4x4 search for speed=0 (good
quality) to guarantee no quality loss for speed0.
Change-Id: Ie04bbc25f7e6a33a7bfa30e05775d33148731c81
The maximum possible MV in 1/8 pel units is (1<<11), which could
cause mvcost out of its range that is 1023. Change maximum
possible MV in 1/8 pel units to (1<<11)-8 will fix this problem.
Change-Id: I5788ed1de773f66658c14f225fb4ab5b1679b74b
Further experiment with restriction of the Q range.
This uses the average non KF/GF/ARF quantizer, instead
of just relying on the initial value. It is not such a strong constraint
but there may be a reduced risk of rate misses.
Change-Id: I424fe782a37a2f4e18c70805e240db55bfaa25ec
The merge includes hooks to for CQ mode and other code
changes merged from the test branch.
CQ mode attempts to maintain a more stable quantizer within a clip
whilst also trying to adhere to a guidline maximum bitrate.
The existing target data rate parameter is used to specify the
guideline maximum bitrate.
A new parameter allows the user to specify a target CQ level.
For normal (non kf/gf/arf) frames, the quantizer will not drop BELOW the
user specified value (0-63). However, in some cases the encoder may
choose to impose a target CQ that is above that specified by the user,
if it estimates that consistent use of the target value is not compatible
with guideline maximum bitrate.
Change-Id: I2221f9eecae8cc3c431d36caf83503941b25e4c1
In two pass encoding each frame is given an active
Q range to work with. This change limits how much this
Q range can be altered over time from the initial estimate
made for the clip as a whole.
There is some danger this could lead to overshoot or undershoot
in some corner cases but it helps considerably in regard to
clips where either there is a glut or famine of bits in some sections,
particularly near the end of a clip.
Change-Id: I34fcd1af31d2ee3d5444f93e334645254043026e
cpi->target_bits_per_mb is currently not being used,
so delete it. Also removed other unused code in rdopt.c.
Change-Id: I98449f9030bcd2f15451d9b7a3b9b93dd1409923
count can be reduced to short because the max number of filtered frames
is set to 15. the max value for any frame is 32 (modifier = 16,
filter_weight = 2). 15*32 = 480 which requires 9 bits
this function goes from about 7000 us / 1000 iterations for the C code
to < 275 us / 1000 iterations for sse2 for block_size = 16 and from
about 1800 us / 1000 iters to < 100 us / 1000 iters for block_size = 8
Change-Id: I64a32607f58a2d33c39286f468b04ccd457d9e6e
The following features don't make sense for the first
pass in its current form and have a significant impact on its
speed (up to 50%).
Slow quantizer, slow dct and trellis optimization.
Change-Id: Id9943f6765ffbd71fc0084ec7dfbc9d376fd6fcd
Calculate a minimum intra value to be used in determining the
IIratio scores used in two pass, second pass.
This is to make sure sections that are low complexity" in the
intra domain are still boosted appropriately for KF/GF/ARF.
For now I have commented out the Q based adjustment of
KF boost.
Change-Id: I15deb09c5bd9b53180a2ddd3e5f575b2aba244b3
