Adds modeled functions to decide the qp for altref frames in constant q
mode similar to other functions in use in bitrate mode.
Also turns on the constrained quality mode (end-usage=2) option which
was turned off before. Basic testing shows the mode works in principle,
to cap bitrate to the target-bitrate specified, while allowing lower
bitrate depending on the cq-level specified. The mode will need to be
improved over time.
Results for constant quality vs bitrate control mode:
derfraw300/fullderfraw: +3.0% at constant quality over bitrate control.
fullstdhdraw: +4.341%
stdhdraw250: +5.361%
Change-Id: If5027c9ec66c8e88d33e47062c6cb84a07b1cda9
Sample app: vp9_spatial_scalable_encoder
vpx_codec_control extensions:
VP9E_SET_SVC
VP9E_SET_WIDTH, VP9E_SET_HEIGHT, VP9E_SET_LAYER
VP9E_SET_MIN_Q, VP9E_SET_MAX_Q
expanded buffer size for vp9_convolve
modified setting of initial width in vp9_onyx_if.c so that layer size
can be set prior to initial encode
Default number of layers set to 3 (VPX_SS_DEFAULT_LAYERS)
Number of layers set explicitly in vpx_codec_enc_cfg.ss_number_layers
Change-Id: I2c7a6fe6d665113671337032f7ad032430ac4197
Adds a new end-usage option for constant quality encoding in vpx. This
first version implemented for VP9, encodes all regular inter frames
using the quality specified in the --cq-level= option, while encoding
all key frames and golden/altref frames at a quality better than that.
The current performance on derfraw300 is +0.910% up from bitrate control,
but achieved without multiple recode loops per frame.
The decision for qp for each altref/golden/key frame will be improved
in subsequent patches based on better use of stats from the first pass.
Further, the qp for regular inter frames may also be varied around the
provided cq-level.
Change-Id: I6c4a2a68563679d60e0616ebcb11698578615fb3
Currently, the best quality mode in VP9 is not very well developed,
and unnecessarily makes the encode too slow. Hence the command line
default is changed to "good" quality. Also, the number of passes
default is changed to 2 passes as well, since 1-pass encoding is
not very efficient in VP9.
Besides, a number of VP9 defaults are set to the currently
recommended settings. With these changes, vpxenc
run with --codec=vp9 --kf-max-dist=9999 --cpu-used=0 should
work about the same as our borg results.
Note when the --cpu-used=0 option is dropped there will be a slight
difference in the output, because of a difference in the cpu-used
value for the first pass. Specifically, the default when unspecified
is to use cpu_used=1 for the first pass and cpu_used=0 for the
second pass. But when specified, both passes will use the cpu-used
value specified.
Note that this also changes the default for VP8 as being "good"
but other options stay unchanged.
Change-Id: Ib23c1a05ae2f36ee076c0e34403efbda518c5066
This patch allows the frame_parallel_decoding_mode flag
to be set instead of returning a codec error.
Change-Id: I4a1631c625723ac8873290d0fd0211074a87d112
Make framebuffer allocations according to the chroma subsamping
factors in use. A bit is placed in the raw part of the frame header for
each of the two subsampling factors. This will be moved in a future
commit to make them part of the TBD feature set bits, probably only set
on keyframes, etc.
Change-Id: I59ed38d3a3c0d4af3c7c277617de28d04a001853
This is work-in-progress, it implements multiple ARF
encoding behind an experimental flag.
It adds the ability to insert multiple ARF frames into a
single ARF group. This patch implements the reordering
of the coded frames, and implements a fixed-length coding
pattern. It applies a fixed quantizer strategy based on
where the frame is in the coding sequence.
Further work to modify the rate control strategy is
ongoing and will be submitted via a set of future patches.
In this first step, each ARF group is recursively
bisected and an ARF frame added at that position in the
sequence. The recursion continues until ARF frames are
within MIN_GF_INTERVAL frames.
The code sits behind the "multiple-arf" experimental
flag ("CONFIG_MULTIPLE_ARF"). The experimental flag
"oneshotq" ("CONFIG_ONESHOTQ") also needs to be enabled
for this patch to work correctly.
Change-Id: Ie473b05ebb43ac473c0cfb659b2b8042823085e2
Renaming Width to width, Height to height and Version to version in
several structs and function signatures.
Change-Id: I084c3f7e747cb2ce3345aff27a3dff9b13a87543
Updates the YV12_BUFFER_CONFIG structure to be crop-aware. The
exiting width/height parameters are left unchanged, storing the
width and height algined to a 16 byte boundary. The cropped
dimensions are added as new fields.
This fixes a nasty visual pulse when switching between scaled and
unscaled frame dimensions due to a mismatch between the scaling
ratio and the 16-byte aligned sizes.
Change-Id: Id4a3f6aea6b9b9ae38bdfa1b87b7eb2cfcdd57b6
This is like VP8_COPY_REFERENCE, but returns a pointer to the reference
frame rather than a copy of it. This is useful when the application
doesn't know what the size of the reference is, as is the case when
scaling is in effect.
Change-Id: I63667109f65510364d0e397ebe56217140772085
If a superframe (ARF) is generated while flushing the lagged frames
at the end of the clip, the buffer pointer wasn't being properly
updated to account for the size of the index, causing the next
frame to overwrite the index on the previous frame.
Change-Id: Ib158cc8e4183d663bdfb9ba002dd4c98916abdc9
A 'superframe' is a group of frames that share the same PTS, but have a
defined decoding order. This commit adds the ability to append an index
to such a group of frames, allowing for random access to the constituent
frames. This could be useful for frame-level parallelism or partial
decoding in a multilayer scenario.
Decoding the stream serially without such an index should work as a
fallback, and VP9/TestSuperframeIndexIsOptional verifies that.
Change-Id: Idff83b7560e1a7077d8fb067bfbc45b567e78b1c
Fixed a couple of variable/function definitions, as well as header
handling to support 16K sequence coding at high bit-rates.
The width and height are each specified by two bytes in the header.
Use an extra byte to explicitly indicate the scaling factors in
both directions, each ranging from 0 to 15.
Tested coding up to 16400x16400 dimension.
Change-Id: Ibc2225c6036620270f2c0cf5172d1760aaec10ec
These allow sending partial bitstream packets over the network before
encoding a complete frame is completed, thus lowering end-to-end
latency. The tile-rows are not independent.
Change-Id: I99986595cbcbff9153e2a14f49b4aa7dee4768e2
This is after discussion with the hardware team. Update the unit test
to take these sizes into account. Split out some duplicate code into
a separate file so it can be shared.
Change-Id: I8311d11b0191d8bb37e8eb4ac962beb217e1bff5
* changes:
Initial support for resolution changes on P-frames
Avoid allocating memory when resizing frames
Adds a test for the VP8E_SET_SCALEMODE control
Allows inter-frames to change resolution. Currently these are
almost equivalent to keyframes, as only intra prediction modes
are allowed, but without the other context resets that occur on
keyframes.
Change-Id: Icd1a2a5af0d9462cc792588427b0a1f5b12e40d3
This patch adds column-based tiling. The idea is to make each tile
independently decodable (after reading the common frame header) and
also independendly encodable (minus within-frame cost adjustments in
the RD loop) to speed-up hardware & software en/decoders if they used
multi-threading. Column-based tiling has the added advantage (over
other tiling methods) that it minimizes realtime use-case latency,
since all threads can start encoding data as soon as the first SB-row
worth of data is available to the encoder.
There is some test code that does random tile ordering in the decoder,
to confirm that each tile is indeed independently decodable from other
tiles in the same frame. At tile edges, all contexts assume default
values (i.e. 0, 0 motion vector, no coefficients, DC intra4x4 mode),
and motion vector search and ordering do not cross tiles in the same
frame.
t log
Tile independence is not maintained between frames ATM, i.e. tile 0 of
frame 1 is free to use motion vectors that point into any tile of frame
0. We support 1 (i.e. no tiling), 2 or 4 column-tiles.
The loopfilter crosses tile boundaries. I discussed this briefly with Aki
and he says that's OK. An in-loop loopfilter would need to do some sync
between tile threads, but that shouldn't be a big issue.
Resuls: with tiling disabled, we go up slightly because of improved edge
use in the intra4x4 prediction. With 2 tiles, we lose about ~1% on derf,
~0.35% on HD and ~0.55% on STD/HD. With 4 tiles, we lose another ~1.5%
on derf ~0.77% on HD and ~0.85% on STD/HD. Most of this loss is
concentrated in the low-bitrate end of clips, and most of it is because
of the loss of edges at tile boundaries and the resulting loss of intra
predictors.
TODO:
- more tiles (perhaps allow row-based tiling also, and max. 8 tiles)?
- maybe optionally (for EC purposes), motion vectors themselves
should not cross tile edges, or we should emulate such borders as
if they were off-frame, to limit error propagation to within one
tile only. This doesn't have to be the default behaviour but could
be an optional bitstream flag.
Change-Id: I5951c3a0742a767b20bc9fb5af685d9892c2c96f
Adds a flag to disable features that would inhibit frame parallel
decoding. This includes backward adaptation and MV sorting based
on search in ref frame buffer.
Also includes some minor clean-ups.
Change-Id: I434846717a47b7bcb244b37ea670c5cdf776f14d
Adds an error-resilient mode where frames can be continued
to be decoded even when there are errors (due to network losses)
on a prior frame. Specifically, backward updates are turned off
and probabilities of various symbols are reset to defaults at
the beginning of each frame. Further, the last frame's mvs are
not used for the mv reference list, and the sorting of the
initial list based on search on previous frames is turned off
as well.
Also adds a test where an arbitrary set of frames are skipped
from decoding to simulate errors. The test verifies (1) that if
the error frames are droppable - i.e. frame buffer updates have
been turned off - there are no mismatch errors for the remaining
frames after the error frames; and (2) if the error-frames are non
droppable, there are not only no decoding errors but the mismatch
PSNR between the decoder's version of the post-error frames and the
encoder's version is at least 20 dB.
Change-Id: Ie6e2bcd436b1e8643270356d3a930e8989ff52a5
Support for gyp which doesn't support multiple objects in the same
static library having the same basename.
Change-Id: Ib947eefbaf68f8b177a796d23f875ccdfa6bc9dc
Modify the decoder to return the ending position of the bool decoder and
use that as the starting position for the next frame.
The constant-space algorithm for parsing the appended frame lengths is
O(n^2), which is a potential DoS concern if n is unbounded. Revisit
the appended lengths for use as partition lengths when multipartition
support is added.
In addition, this allows decoding of raw streams outside of a container
without additional framing information, though it's insufficient to
be able to remux said stream into a container.
Change-Id: I71e801a9c3e37abe559a56a597635b0cbae1934b
The altref frame is packed along with the next P frame. So that
outside of the codec there are now only two types of frames P and I.
Also, now it is one frame in and one frame out with respect to the
codec. Apart from that, all the frames are length encoded with the
length of each frame appended to the frame itself. There are
two categories of frames and each of them will look as follows:
- Packed frames (an altref along with the succeeding p frame)
- altref_frame_data | altref_lenngth | frame_data | length
- Unpacked frames (all frames other than the above)
- frame_data | length
Change-Id: If1eabf5c473f7d46b3f2d026bd30c803588c5330
there are still a couple type of warning left, which are related to
double constants assigned to float type. As those would be addressed
by the conversion of transforms into integer version. This commit
has left those un-dealt with.
Change-Id: I48fd9b489c0c27ad6b543f4177423419f929f2bb
