error_per_bit and sad_per_bit were designed as estimates of a bit worth
of sum squared error and sum absolute difference respectively. Under
this assumption, error_per_bit should be used in combination with 2nd
order errors (variance or sum squared error) while sad_per_bit should
be used in combination with 1st order SADs in motion estimation. There
were a few places where sad_per_bit has been misused with variances,
this commit changes to use error_per_bit for those places, also changes
parameter names to properly indicate which constant is being used.
On cif set, the change has a universal gain by all metrics: 0.13% by
average/overall psnr and 0.1% by ssim.
Change-Id: I4850fdcc3fd6886b30f784bd843f13dd401215fb
While profile=3, there is no sub-pixel search. Distortion and SSE
have to calculated using get_inter_mbpred_error().
Change-Id: Ifb36e17eef7750af93efa7d0e2870142ef540184
Declared the bmi in MODE_INFO as a union instead of B_MODE_INFO.
This reduced the memory footprint by 518,400 bytes for 1080
resolutions. The decoder performance improved by ~4% for the
clip used and the encoder showed very small improvements. (0.5%)
This reduction was first mentioned to me by John K. and in a
later discussion by Yaowu.
This is WIP.
Change-Id: I8e175fdbc46d28c35277302a04bee4540efc8d29
fixed a bug where active_worst_quality could be set
below active_best_quality which could result in an
infinite loop.
Change-Id: I93c229c3bc5bff2a82b4c33f41f8acf4dd194039
This patch collects the twopass specific memebers of VP8_COMP into a
dedicated struct. This is a first step towards isolating the two pass
rate control and aids readability by decorating these variables with
the 'twopass.' namespace. This makes it clear to the reader in what
contexts the variable will be valid, and is a hint that a section of
code might be a good candidate to move to firstpass.c in later
refactoring. There likely will be other rate control modes that need
their own specific data as well.
This notation is probably overly verbose in firstpass.c, so an
alternative would be to access this struct through a pointer like
'rc->' instead of 'cpi->firstpass.' in that file. Feel free to make
a review comment to that effect if you prefer.
Change-Id: I0ab8254647cb4b493a77c16b5d236d0d4a94ca4d
The partition_info struct contains info just for SPLITMV,
so it should be used instead of BLOCKD. Eventually, I want
to reduce the size of B_MODE_INFO struct found in BLOCKD, so
this is the first step toward that goal.
Also, since SPLITMV is not supported in vp8_pick_inter_mode(),
the unnecessary mem copies and checks were removed. For rt
encodes, this gave a slight performance improvement.
Change-Id: I5585c98fa9d5acbde1c7e0f452a01d9ecc080574
The error-concealer is plugged in after any motion vectors have been
decoded. It tries to estimate any missing motion vectors from the
motion vectors of the previous frame. Intra blocks with missing
residual are replaced with inter blocks with estimated motion vectors.
This feature was developed in a separate sandbox
(sandbox/holmer/error-concealment).
Change-Id: I5c8917b031078d79dbafd90f6006680e84a23412
rvct 4.1 was complaining about vstmia.16, store multiple expects 64 data type.
optimized the implementation.
Change-Id: I0701052cabd685c375637bbc3796ff6d88f5972c
This commit restructures the mb activity masking code
to better facilitate experimentation using different metrics
etc. and also allows for adjustment of the zero bin either
for encode only or both the encode and mode selection
stages
It also uses information from the current frame rather than
the previous frame and the default strength has been
reduced.
Change-Id: Id39b19eace37574dc429f25aae810c203709629b
