Moved vp8_fast_quantize_b_sse from quantize_mmx.asm into
quantize_sse2.asm and renamed. Updated the assembly code to
match the C version.
Change-Id: I1766d9e1ca60e173f65badc0ca0c160c2b51b200
As the zbin and rounding constants are normalized, rounding effectively
does the zbinning, therefore the zbin operation can be removed. In
addition, the memset on the two arrays are no longer necessary.
Change-Id: If39c353c42d7e052296cb65322e5218810b5cc4c
Filed for nasm as:
https://sourceforge.net/tracker/?func=detail&atid=106208&aid=3081103&group_id=6208
nasm just does not accept any size parameter for movhps:
1.asm:2: error: mismatch in operand sizes
Some parts of libvpx already use MMWORD for movhps and MMWORD is
defined-out so it is compatible both with yasm and nasm.
Provide nasm compatibility. No binary change by this patch with yasm on
{x86_64,i686}-fedora13-linux-gnu.
Change-Id: I4008a317ca87ec07c9ada958fcdc10a0cb589bbc
nasm does not support `label wrt rip', it requires `rel label'. It is
still fully compatible with yasm.
Provide nasm compatibility. No binary change by this patch with yasm on
{x86_64,i686}-fedora13-linux-gnu. Few longer opcodes with nasm on
{x86_64,i686}-fedora13-linux-gnu have been checked as safe.
Change-Id: I488773a4e930a56e43b0cc72d867ee5291215f50
nasm requires the instruction length (movd/movq) to match to its
parameters. I find it more clear to really use 64bit instructions when
we use 64bit registers in the assembly.
Provide nasm compatibility. No binary change by this patch with yasm on
{x86_64,i686}-fedora13-linux-gnu. Few longer opcodes with nasm on
{x86_64,i686}-fedora13-linux-gnu have been checked as safe.
Change-Id: Id9b1a5cdfb1bc05697e523c317a296df43d42a91
Raised by Lei Yang, the Y plane stride was used for UV blocks.
This is clearly a typo. But as the comments in the code suggested
that this port of code has not been used yet, so the typo should
not have created any damage yet.
Change-Id: Iea895edc17469a51c803a8cc6d0fce65a1a7fc2f
This code adjust the impact of the amount and speed of motion
on GF and KF boost.
Sections with lots of slow motion will tend to have a
somewhat bigger boost and sections with fast motion may
have less.
There is a knock on effect to the selection of the active
quantizer range.
This will likely require further tuning but helps with a couple
of particularly bad edge cases.
Change-Id: Ic2449cda7305672b69acf42fc0a845b77ac98d40
Experimented with different value for Y2_RD_MULT ranging f[1, 32],
without adapting the value to MB coding mode/frame type/Q value,
4 works out best among all values, providing overall 0.1% coding
gain on the test set.
Change-Id: I6b2583a8aa5db5e7e5c65c646301909c0c58f876
If temporal filtering is enabled but a filter type is not specified
centered filter mode is used by default.
Change-Id: I87306f267c1390074c806c506a69b4ba914d92a2
Modified the range checking of parameters used in the
AltRef temporal filter (arnr-max-frames, arnr-strength,
arnr-type) and default values for each of them.
Change-Id: Ib261028d501b9523f6e44cb4790cc52167b6e92b
This function graduated from being a test func to something that's on
by default. Rename it and remove some spurious comments that confuse
its status.
Change-Id: I689695a3ad29c35e9a72a43ec93766733ac6c20b
Loopfilter deltas are initialized to zero on keyframes in the decoder.
The values then persist from the previous frame unless an update bit
is set in the bitstream. This data is not included in the entropy
data saved by the 'refresh entropy' bit in the bitstream, so it is
effectively an additional contextual element beyond the 3 ref-frames
and the entropy data.
The encoder was treating this delta update bit as update-if-nonzero,
meaning that the value would be refreshed even if it hadn't changed,
and more significantly, if the correct value for the delta changed
to zero, the update wouldn't be sent, and the decoder would preserve
the last (presumably non-zero) value.
This patch updates the encoder to send an update only if the value
has changed from the previously transmitted value. It also forces the
value to be transmitted in error resilient mode, to account for lost
context in the event of lost frames.
Change-Id: I56671d5b42965d0166ac226765dbfce3e5301868
Create look up tables for controlling the active quantizer range.
Some initial tuning to improve quality circa 0.5% on test set.
Clean up of some stats output code
Change-Id: Ia698a8525f8b8129a503cadace3ee73fe888f543
- Scheduling for Atom processors
- Combining of macros to allow for better interleaving
- Change from multiplies to adds for main filter
- Use of movhps/movlps to fill xmm registers without
shifting and orring
Change-Id: I0b3500a5f58abf7085253ec92d64c8a96723040b
Modified AltRef temporal filter to adapt filter length based
on macroblock coding modes selected during first-pass
encode.
Also added sub-pixel motion compensation to the AltRef
filter.
The existing code applied a 6-tap filter with 0's on either end.
We're already paying the branch penalty to avoid computing the two
extra columns needed as input to this filter.
We might as well save time computing the filter as well.
This reduces the inner loop from 21 instructions to 16, the number
of loads per iteration from 4 to 1, and the number of multiplies
from 7 to 4.
The gain in overall decoding performance, however, is small (less
than 1%).
This change also means we now valgrind clean on ARMv6, which is
its real purpose.
The errors reported here were valgrind's fault (it does not detect
that 0 times an uninitialized value is initialized), but Julian
Seward says it would slow down valgrind considerably to make such
checks.
Speeding up libvpx rather, even by a small amount, seems a much
better idea if only to enable proper valgrind checking of the
rest of the codec.
Change-Id: Ifb376ea195e086b60f61daf1097d8910c4d8ff16
This function was accessing values below the stack pointer, which
can be corrupted by signal delivery at any time.
Change-Id: I92945b30817562eb0340f289e74c108da72aeaca
previous implementation compared each set of values to limit and then
&'d them together, requiring a compare and & for each value.
this does the accumulation first, requiring only one compare
Change-Id: Ia5e3a1a50e47699c88470b8c41964f92a0dc1323
This patch avoids compiling some debugging code in onyx_if.c. The most
significant fix is to avoid generating code for vp8_write_yuv_frame,
which is never called. Some other code was removed by the dead code
elimination performed by the compiler, and this patch does it with the
preprocessor instead. There are advantages both ways.
Change-Id: I044fd43179d2e947553f0d6f2cad5b40907ac458
reconintra_mt.c is only required for building the decoder right now.
It could definitely be used for the encoder in the future, but it
currently depends on decoder only data structures. (onyxd_int.h,
VP8D_COMP, etc). Move it from common/ to decoder/ until the
necessary changes to the common multithread code are complete.
This patch is needed to build with --disable-vp8-decoder.
Change-Id: I568c52221a2b309234d269675cba97131ce35c86
Having these symbols be available as functions rather than data is
occasionally more convenient. Implemented this way rather than a
get-codec-by-id style to avoid creating a link-time dependency
between the encoder and the decoder.
Fixes issue #169
Change-Id: I319f281277033a5e7e3ee3b092b9a87cce2f463d
The MV decoding changes in c5fb0eb introduced a bug where the
macroblock clamping state was reset for each partition, so if an
earlier partition needed clamping but a subsequent one didn't,
the MB wouldn't receive clamping. Instead, the state is only
set during splitmv decoding, never cleared.
Change-Id: I224fe258493405ee0f6a04596acdb622c475e845
Movdqu is more expensive (throughput, uops) than movq. Minimal
impact for newer big cores, but ~2.25% gain on Atom.
Change-Id: I62c80bb1cc01d8a91c350c4c7719462809a4ef7f
Use pmaxub instead of a combination of psubusb/por to
determine if any comparisons go over the limit.
Change-Id: I3f0bd7d2aabe5fee9ba6620508e2b60605abcb82
The patch related with issue #55 (5a72620) fixed some warnings, but the
fix was not optimal. It actually was a trick to confuse compiler rather
than a fix.
This patch fixes it by creating a new macro used when needed just a high
limit check for an unsigned.
Change-Id: I94b322e0f7fb07604b3b1df1f9321185f48cfcb5
the previous commit laid the groundwork by doing two sets of idcts
together. this moved that further by grouping the interesting data
(q[0], q+16[0]) together to allow using wider instructions. also
managed to drop a few instructions by recognizing that the constant
for sinpi8sqrt2 could be downshifted all the time which avoided a
dowshift as well as workarounds for a function which only accepted
signed data
looks like a modest gain for performance: at qcif, went from ~180
fps to ~183
Change-Id: I842673f3080b8239e026cc9b50346dbccbab4adf
On each MB, loopfiltering is done right after MB decoding. This
combines two loops in multi-threaded code into one, which reduces
number of synchronizations to half.
The above-row/left-col data are saved in temp buffers for
next-row/next MB decoding.
Tests on 4-core gLucid machine showed 10% decoder performance
gain with threads=4 (tulip clip). Testing on other platforms
isn't done yet.
Change-Id: Id18ea7c1e84965dabea65d4c01ca5bc056ddeac9
This patch reduces the size of the global tables maintained by the
tokenizer to 16k from 80k-96k. See issue #177.
Change-Id: If0275d5f28389af11ac83c5d929d1157cde90fbe
Modified code so that:
-When above and left contexts are same and not equal to current segment id, it needs to read a maximum of 2 segment_tree_probabilities.
- When above and left contexts are different and not equal to current segment id, it needs to read only a single segment_tree_probability.
Change-Id: Idc2cf2c4afcc6179b8162ac5a32c948ff5a9a2ba
There is no need to make sure that the lower byte of the
register is 0 because the downshift by 11 overwrites that byte.
Change-Id: I89cbf004b2ff532a2c68e0dc399c45a49cdad5a1
-Updates by making use of spatial correlation.
-Checks if the segment_id is same as above or left context and encodes only the update to the map instead of updating individual segment_ids.
Change-Id: Ib861df97e8aa2b37516219eeddcdbaf552b6a249
Sequentially accessing memory from a low address to a high
address should make it easier for the processor to predict
the cache.
Change-Id: I1921ce996bdd547144fe864fea6435f527f5842d
Improved the subset block search and fill. (about 3% improvement for
32 bit) Modified/merged the code in order to create
vp8_read_mb_modes_mv which can decode the modes/mvs on a macroblock
level. This will allow the decode loop (in the future) to decode
modes/mvs on a frame, row, or mb level.
Change-Id: If637d994b508792f846d39b5d44a7bf9aa5cddf3
Expand 93c32a55 which used SSE2 instructions to do two
idct/dequant/recons at a time to NEON. Initial working
commit. More work needs to be put into rearranging and
interlacing the data to take advantage of quadword
operations, which is when we'll hopefully see a much
better boost
Change-Id: I86d59d96f15e0d0f9710253e2c098ac2ff2865d1
When ARFs are enabled in non-lagged compress modes, the GF interval
was being reset to zero. Non-lagged ARF updates were enabled in commit
63ccfbd, but this incorrect GF interval caused a quality regression.
Change-Id: I615c3b493f4ce2127044f4e68d0bcb07d6b730c3
Changes 'The VP8 project' to 'The WebM project', for consistency
with other webmproject.org repositories.
Fixes issue #97.
Change-Id: I37c13ed5fbdb9d334ceef71c6350e9febed9bbba
vp8_get_compressed_data() was defeating logic in
encode_frame_to_datarate() that determined the reference buffers to
search and forcing all frames to be eligible to search. In cases
where buffers have identical contents, this is unnecessary extra
work.
Change-Id: I9e667ac39128ae32dc455a3db4c62e3efce6f114
ARFs were explicitly disabled except in lagged compress mode. New
ARF logic allows for the ARF buffer to hold an older golden frame,
which does not require lagged compress.
Change-Id: I1dff82b6f53e8311f1e0514b1794ae05919d5f79
Moved partition_bmi and partition_count out of MB_MODE_INFO and
placed into MACROBLOCK. Also reduced the size of other members
of the MB_MODE_INFO struct. For 1080p, the memory was reduced
by 1,209,516 bytes. The decoder performance appeared to improve
by 3% for the clip used.
Note: The main goal for this change is to improve the decoder
performance. The encoder will be revisited at a later date for
further structure cleanup.
Change-Id: I4733621292ee9cc3fffa4046cb3fd4d99bd14613
Remove the dependency on postproc.c for the encoder in general, the only
unchecked need for it is when CONFIG_PSNR is enabled. All other cases
are already wrapped in CONFIG_POSTPROC. In the CONFIG_PSNR case the file
will still be included.
Additionally, when VP8_SET_POSTPROC is used with the encoder when post
processing has been disabled an error will be returned.
This addresses issue #153.
Change-Id: Ia6dfe20167f7077734a6058cbd1d794550346089
There was an extremely rare deadlock that happened when one thread
was waiting to start the loop filter on frame n while the other
threads were starting to work on frame n+1.
Change-Id: Icc94f728b3b6663405435640d9a2996735ba19ef
These changes improve the behaviour of the code with
forced key frames sent in by a calling application.
The sizing of the frames is still suboptimal for two pass in
particular but the behaviour is much better than it was.
Change-Id: I35fae610c67688ccc69d11f385e87dfc884e65a1
The main reason for the change was to reduce cycles in the token
decoder. (~1.5% gain for 32 bit) This layout should be more
cache friendly.
As a result of this change, the encoder had to be updated.
Change-Id: Id5e804169d8889da0378b3a519ac04dabd28c837
Note: dixie uses a similar layout
The memory being zeroed in vp8_update_mode_info_border() was just
allocated with calloc, and so the entire function is actually
redundant, but it should be made correct in case someone expects
it to actually work in the future.
Change-Id: If7a84e489157ab34ab77ec6e2fe034fb71cf8c79
did a test compile with clang and got rid of some warnings that have
been annoying me for a while:
vp8/decoder/detokenize.c: In function 'vp8_init_detokenizer':
vp8/decoder/detokenize.c:121: warning: assignment discards qualifiers from pointer target type
vp8/decoder/detokenize.c:122: warning: assignment discards qualifiers from pointer target type
vp8/decoder/detokenize.c:123: warning: assignment from incompatible pointer type
vp8/decoder/detokenize.c:124: warning: assignment discards qualifiers from pointer target type
vp8/decoder/detokenize.c:125: warning: assignment discards qualifiers from pointer target type
vp8/decoder/detokenize.c:128: warning: assignment discards qualifiers from pointer target type
vp8/decoder/detokenize.c:129: warning: assignment discards qualifiers from pointer target type
vp8/decoder/detokenize.c:130: warning: assignment discards qualifiers from pointer target type
vp8/decoder/detokenize.c:131: warning: assignment discards qualifiers from pointer target type
Change-Id: I78ddab176fe47cbeed30379709dc7bab01c0c2e4
Moving the eob structure allows for a non-struct based
function to handle decoding an entire mb of
idct/dequant/recon data. This allows for SIMD functions
to idct/dequant/recon multiple blocks at once.
SSE2 implementation gives 3% gain on Atom.
Change-Id: I8a8f3efd546ea4e0535f517d94f347cfb737c9c2
The external API exposes the RC initial/optimal/full buffer level in
milliseconds, but this value was truncated internally to seconds. This
patch allows the use of the full precision during the conversion from
time to bits.
Change-Id: If8dd2a87614c05747f81432cbe75dd9e6ed2f04e
move some things around, reorder some instructions
constant 0 is used several times. load it once per call in horiz,
once per loop in vert.
separate saturating instructions to avoid stalls.
just use one usub8 call to set GE flags, rather than uqsub8 followed by
usub8 w/ 0
document some stalls for further consideration
Change-Id: Ic3877e0ddbe314bb8a17fd5db73501a7d64570ec
test cases were causing a crash because the count was being read
incorrectly. after fixing that, noticed that the output was not
matching. fixed that.
Change-Id: Idb0edb887736bd566a3cf6d4aa1a03ea8d20eb27
The C version of the dequant/idct/add function depends on the C
version of the IDCT, but this isn't compiled in on ARM. Since this
code has asm version, we can just remove this file to eliminate the
link error.
Change-Id: I21de74d89d3765a1db2da27292b20727c53178e9
vp8_update_gf_useage_maps() is only used by the encoder. This patch
fixes the ability to build in decode-only or encode-only
configurations.
Change-Id: I3a5211428e539886ba998e09e8abd747ac55c9aa
adds a compile time option: --enable-arm-asm-detok which pulls in
vp8/decoder/arm/detokenize.asm
currently about break even speed wise, but changes are pending to
the fill code (branch and load 3 bytes versus conditionally always
load one) and the error handling. Currently it doesn't handle zero
runs or overrunning the buffer.
this is really just so i don't have to rebase my changes all the
time to run benchmarks - now just need to replace one file!
Change-Id: I56d0e2354dc0ca3811bffd0e88fe1f952fa6c797
asm_offsets contains some definitions which are no longer used. this
was one of them. v6 build works now
Change-Id: If370cfa8acd145de4fead2d9a11b048fccc090df
These copies occurred for each macroblock in the encoder and decoder.
Thetemp MB_MODE_INFO mbmi was removed from MACROBLOCKD. As a result,
a large number compile errors had to be fixed.
Change-Id: I4cf0ffae3ce244f6db04a4c217d52dd256382cf3
The mv_ref and sub_mv_ref token encodings are indexed from NEARESTMV
and LEFT4X4, respectively, rather than being zero-based like the
other token encodings.
Change-Id: I3699c3f84111209ecfb91097c4b900773e9a3ad5
This patch changes a few numbers in the two constant arrays
for quantizer's zerobin and rounding factors, in general to
make the sum of the two factors for any Q to be 128. While
it might be beneficial to calibrate the two arrays for best
quantizer performance, it is not the purpose of this patch.
Normalizing the two arrays will enable quick optimization
of the current faster quantizer, i.e .zerobin check can be
removed.
Change-Id: If9abfd7929bf4b8e9ecd64a79d817c6728c820bd
Replace the exponential search for optimal rounding during
quantization with a linear Viterbi trellis and enable it
by default when using --best.
Right now this operates on top of the output of the adaptive
zero-bin quantizer in vp8_regular_quantize_b() and gives a small
gain.
It can be tested as a replacement for that quantizer by
enabling the call to vp8_strict_quantize_b(), which uses
normal rounding and no zero bin offset.
Ultimately, the quantizer will have to become a function of lambda
in order to take advantage of activity masking, since there is
limited ability to change the quantization factor itself.
However, currently vp8_strict_quantize_b() plus the trellis
quantizer (which is lambda-dependent) loses to
vp8_regular_quantize_b() alone (which is not) on my test clip.
Patch Set 3:
Fix an issue related to the cost evaluation of successor
states when a coefficient is reduced to zero. With this
issue fixed, now the trellis search almost exactly matches
the exponential search.
Patch Set 2:
Overall, the goal of this patch set is to make "trellis"
search to produce encodings that match the exponential
search version. There are three main differences between
Patch Set 2 and 1:
a. Patch set 1 did not properly account for the scale of
2nd order error, so patch set 2 disable it all together
for 2nd blocks.
b. Patch set 1 was not consistent on when to enable the
the quantization optimization. Patch set 2 restore the
condition to be consistent.
c. Patch set 1 checks quantized level L-1, and L for any
input coefficient was quantized to L. Patch set 2 limits
the candidate coefficient to those that were rounded up
to L. It is worth noting here that a strategy to check
L and L+1 for coefficients that were truncated down to L
might work.
(a and b get trellis quant to basically match the exponential
search on all mid/low rate encodings on cif set, without
a, b, trellis quant can hurt the psnr by 0.2 to .3db at
200kbps for some cif clips)
(c gets trellis quant to match the exponential search
to match at Q0 encoding, without c, trellis quant can be
1.5 to 2db lower for encodings with fixed Q at 0 on most
derf cif clips)
Change-Id: Ib1a043b665d75fbf00cb0257b7c18e90eebab95e
This is the first modification of VP8 multi-thread decoder, which uses
same threads to decode macroblocks and then do loopfiltering for each
frame.
Inspired by Rob Clark, synchronization was done on every 8 macroblocks
instead of every macroblock to reduce lock contention.
Comparing with the original code, this implementation gave about 15%-
20% performance gain while decoding my test clips on a Core2 Quad
platform (Linux).
The work is not done yet.
Test on other platforms are needed.
Change-Id: Ice9ddb0b511af1359b9f71e65066143c04fef3b5
Clang defaults to C99 mode, and inline works differently in C99.
(gcc, on the other hand, defaults to a special gnu-style inlining,
which uses different syntax.) Making the functions static makes sure
clang doesn't decide to discard a function because it's too large to
inline.
Thanks to eli.friedman for the patch.
Fixes http://code.google.com/p/webm/issues/detail?id=114
Change-Id: If3c1c3c176eb855a584a60007237283b0cc631a4
global label:data
^^
Provide nasm compatibility. No binary change by this patch with yasm
on {x86_64,i686}-fedora13-linux-gnu. Few longer opcodes with nasm on
{x86_64,i686}-fedora13-linux-gnu have been checked as safe.
Change-Id: I10f17eb1e4d4a718d4ebd1d0ccddc807c365e021
Labels should end by colon (':'), nasm requires it.
Provide nasm compatibility. No binary change by this patch with yasm
on {x86_64,i686}-fedora13-linux-gnu. Few longer opcodes with nasm on
{x86_64,i686}-fedora13-linux-gnu have been checked as safe.
Change-Id: I0b2ec6f01afb061d92841887affb5ca0084f936f
nasm knows only OWORD. yasm knows both OWORD and DQWORD.
Provide nasm compatibility. No binary change by this patch with yasm on
{x86_64,i686}-fedora13-linux-gnu. Few longer opcodes with nasm on
{x86_64,i686}-fedora13-linux-gnu have been checked as safe.
Change-Id: I62151390089e90df9a7667822fa594ac20b00e78
Removed the global variables vp8_an and vp8_cd. vp8_an was causing problems
because it was increasing the .bss by 1572864 bytes.
Change-Id: I6c12e294133c7fb6e770c0e4536d8287a5720a87
To facilitate more testing related to quantizer and rate
control, the old version quantizer is added back. old and
new quantizer can be switched back and forth by define or
un-define the macro "EXACT_QUANT".
Change-Id: Ia77e687622421550f10e9d65a9884128a79a65ff
follow up to Change I0e51492d: neon: disable asm quantizer
Now x86 doesn't segfault with --disable-runtime-cpu-detect and -p=2
Change-Id: I8ca127bb299198efebbcbd5a661e81788361933f
The assembly version of the quantizer has not been updated to match
the new exact quantizer introduced in commit e04e2935. That commit tried
to disable this code but missed the non-RTCD case.
Thanks to David Baker <david.baker at openmarket.com> for isolating the
issue and testing this fix.
Change-Id: I0e51492dc6f8e44d2c10b587427448bf94135c65
Jeff Muizelaar posted some changes to the idct/reconstruction c code.
This is the equivalent update for the arm assembly.
This shows a good boost on v6, and a minor boost on neon.
Here are some numbers for highway in qcif, 2641 frames:
HEAD neon: ~161 fps
new neon: ~162 fps
HEAD v6: ~102 fps
new v6: ~106 fps
The following functions have been updated for armv6 and neon:
vp8_dc_only_idct_add
vp8_dequant_idct_add
vp8_dequant_dc_idct_add
Conflicts:
vp8/decoder/arm/armv6/dequantdcidct_v6.asm
vp8/decoder/arm/armv6/dequantidct_v6.asm
Resolved by removing these files. When I rewrote the functions, I also
moved the files to dequant_dc_idct_v6.asm/dequant_idct_v6.asm
Change-Id: Ie3300df824d52474eca1a5134cf22d8b7809a5d4
This moves the prediction step before the idct and combines the idct and
reconstruction steps into a single step. Combining them seems to give an
overall decoder performance improvement of about 1%.
Change-Id: I90d8b167ec70d79c7ba2ee484106a78b3d16e318
At the end of the decode, frame buffers were being copied.
The frames are not updated after the copy, they are just
for reference on later frames. This change allows multiple
references to the same frame buffer instead of copying it.
Changes needed to be made to the encoder to handle this. The
encoder is still doing frame buffer copies in similar places
where pointer reference could be done.
Change-Id: I7c38be4d23979cc49b5f17241ca3a78703803e66
In two pass encodes, the calculation of the number of bits
allocated to a KF group had the potential to overflow for high data
rates if the interval is very long.
We observed the problem in one test clip where there was one
section where there was an 8000 frame gap between key frames.
Change-Id: Ic48eb86271775d7573b4afd166b567b64f25b787
This replaces the approximate division-by-multiplication in the
quantizer with an exact one that costs just one add and one
shift extra.
The asm versions have not been updated in this patch, and thus
have been disabled, since the new method requires different
multipliers which are not compatible with the old method.
Change-Id: I53ac887af0f969d906e464c88b1f4be69c6b1206
These files were out of date and no longer maintained.
Token decoding has implemented the no-crash code which
is incompatible with this arm assembly code.
Change-Id: Ibf729886c56fca48181af60b44bda896c30023fc
The libs.mk file must be installed for the vpx.vcproj file to be
generated. It was being installed, but not in the src/ directory as
expected.
Also missed include files yasm.rules, quantize_x86.h
Change-Id: Ic1a6f836e953bfc954d6e42a18c102a0114821eb
Change submitted for Adrian Grange. Convert threshold
calculation in ARNR filter to a lookup table.
Change-Id: I12a4bbb96b9ce6231ce2a6ecc2d295610d49e7ec
Previously we had assumed that it was necessary to give a full frame's
bit allocation to the alt ref frame if it has been created through temporal
filtering. This is not the case. The active max quantizer control
insures that sufficient bits are allocated if needed and allocating a
full frame's worth of bits creates an excessive overhead for the ARF.
Change-Id: I83c95ed7bc7ce0e53ccae6ff32db5a97f145937a
In the case where the best reference mv is not (0,0) a secondary
search is carried out centered on (0,0). However, rather than
sending tmp_err into the search function, motion_error was
inadvertently passed.
As a result tmp_err remains set at INT_MAX and the (0,0)-based
search result will never be selected, even if it is better.
Change-Id: I3c82b246c8c82ba887b9d3fb4c9e0a0f2fe5a76c
Change I9fd1a5a4 updated the multithreaded loopfilter to avoid
reinitializing several parameteres if they haven't changed from the
last frame, but the code to update the last frame's parameters wasn't
invoked in the multithreaded case.
Change-Id: Ia23d937af625c01dd739608e02d110f742b7e1f2
Restructured and rewrote SSE2 loopfilter functions. Combined u and
v into one function to take advantage of SSE2 128-bit registers.
Tests on test clips showed a 4% decoder performance improvement on
Linux desktop.
Change-Id: Iccc6669f09e17f2224da715f7547d6f93b0a4987
Following conversations with Tim T (Derf) I ran a large number of
tests comparing the existing polynomial expression with a simpler
^2 variant. Though the polynomial was sometimes a little better at
the extremes of Q it was possible to get close for most clips and
even a little better on some.
This code also changes the way the RD multiplier is calculated
when the ZBIN is extended to use a variant of the same ^2
expression.
I hope that this simpler expression will be easier to tune further
as we expand our test set and consider adjustments based on content.
Change-Id: I73b2564346e74d1332c33e2c1964ae093437456c
Besides the slight improvement in round trip error. This
also fixes a sign bias in the forward transform, so the
round trip errors are evenly distributed between +1s and
-1s. The old bias seemed to work well with the dc sign bias
in old fdct, which no longer exist in the improved fdct.
Change-Id: I8635e7be16c69e69a8669eca5438550d23089cef
Corrected setting of "which_buffer" for U & V cases to match that
used for Y, i.e. to refer to the temporally most recent frame of
those to be filtered.
Change-Id: Idf94b287ef47a05f060da3e61134a0b616adcb6b
The new fdct lowers the round trip sum squared error for a
4x4 block ~0.12. or ~0.008/pixel. For reference, the old
matrix multiply version has average round trip error 1.46
for a 4x4 block.
Thanks to "derf" for his suggestions and references.
Change-Id: I5559d1e81d333b319404ab16b336b739f87afc79
bestsad needs to be a int and set to INT_MAX because at the end
of the function it is compared to INT_MAX to determine if there
was a match in the function.
Change-Id: Ie80e88e4c4bb4a1ff9446079b794d14d5a219788
bestsad should be an int initialized to INT_MAX. The optimized
SAD function expects a signed value for bestsad to use for comparison
and early loop termination. When no match is made, which is
determined by a comparison of bestsad to INT_MAX, INT_MAX is returned.
These are mostly vestigial, it's up to the compiler to decide what
should be inlined, and this collided with certain Windows platform SDKs.
Change-Id: I80dd35de25eda7773156e355b5aef8f7e44e179b
1. Unavailability of each reference frame type should be tested
independently,
2. Also, only the VP8_GOLD_FLAG needs to be tested before setting
golden frame specific thresholds, and only VP8_ALT_FLAG needs
testing before setting thresholds relevant to the AltRef frame.
(Raised by gbvalor, in response to Issue 47)
Change-Id: I6a06fc2a6592841d85422bc1661e33349bb6c3b8
Since the intent is
to reset the appropriate bit in ref_frame_flags not to
test a logic condition. Prior result would always have
been ref_frame_flags being set to 0.
(Issue reported by dgohman, issue 47)
Change-Id: I2c12502ed74c73cf38e98c9680e0249c29e16433
The DOUBLE_DIVIDE_CHECK macro prevents from divide by 0,
so must be on the denominator to work as intended.
Change-Id: Ie109242d52dbb9a2c4bc1e11890fa51b5f87ffc7
If the version script produced by the libvpx build system is not
used when linking a shared library on x86-64 Linux, the constant
data in the subpel filters produces R_X86_64_32 relocation errors
due to the use of wrt rip addressing instead of
wrt rip wrt ..gotpcrel.
Instead of adding a new macro for this addressing mode, this patch
sets the ELF visibility of these symbols to "hidden", which
allows wrt rip addressing to work without a text relocation.
This allows building a shared library without using the provided
build system or a separate version script.
Fixes http://code.google.com/p/webm/issues/detail?id=46
Change-Id: Ie108f9d9a4352e5af46938bf4750d2302c1b2dc2
When the license headers were updated, they accidentally contained
trailing whitespace, so unfortunately we have to touch all the files
again.
Change-Id: I236c05fade06589e417179c0444cb39b09e4200d
Change bitreading functions to use a larger window which is refilled less
often.
This makes it cheap enough to do bounds checking each time the window is
refilled, which avoids the need to copy the input into a large circular
buffer.
This uses less memory and speeds up the total decode time by 1.6% on an ARM11,
2.8% on a Cortex A8, and 2.2% on x86-32, but less than 1% on x86-64.
Inlining vp8dx_bool_decoder_fill() has a big penalty on x86-32, as does moving
the refill loop to the front of vp8dx_decode_bool().
However, having the refill loop between computation of the split values and
the branch in vp8_decode_mb_tokens() is a big win on ARM (presumably due to
memory latency and code size: refilling after normalization duplicates the
code in the DECODE_AND_BRANCH_IF_ZERO and DECODE_AND_LOOP_IF_ZERO cases.
Unfortunately, refilling at the end of vp8dx_bool_decoder_fill() and at the
beginning of each decode step in vp8_decode_mb_tokens() means the latter
requires an extra refill at the end.
Platform-specific versions could avoid the problem, but would require most of
detokenize.c to be duplicated.
Change-Id: I16c782a63376f2a15b78f8086d899b987204c1c7
Added sse2 version of vp8_regular_quantize_b which improved encode
performance(for the clip used) by ~10% for 32 bit builds and ~3% for
64 bit builds.
Also updated SHADOW_ARGS_TO_STACK to allow for more than 9 arguments.
Change-Id: I62f78eabc8040b39f3ffdf21be175811e96b39af
This patch addresses issue #79, which is a regression since commit
28de670 "Fix RD bug." If the coded error value is zero, the iiratio
calculation effectively multiplies by 1000000 by the
DOUBLE_DIVIDE_CHECK macro. This can result in a value larger than
INT_MAX, giving a negative ratio. Since the error values are
conceptually unsigned (though they're stored in a double) this patch
makes the iiratio values unsigned, which allows the clamping to work
as expected.
ssim.c comiles in a huge (512M) amount of global scratch space. Allocating
this data on the heap would be a better solution, but this file doesn't
need to be built at all in most cases, so as a first pass, disable it
except when doing opsnr.stt output (--enable-psnr).
Change-Id: I320d812f6d652a12516a16b52295ebff20b5bd42
No good reason to be tricky here. I don't know why 'break' occurred to me
as the natrual replacement for the 'return', but an if/else block is
definitely clearer.
Change-Id: I08a336307afeb0dc7efa494b37398f239f66c2cf
The new scheme introduced in I68d35a2f did not clamp chroma MVs in the SPLITMV
case, and clamped them incorrectly (to the luma plane bounds) in every other
case.
Because chroma MVs are computed from the luma MVs before clamping occurs, they
could still point outside of the frame buffer and cause crashes.
This clamping happens outside of the MV prediction loop, and so should not
affect bitstream decoding.
Restructure vp8_sixtap_predict functions to eliminate extra 5-line
calculation while doing first-pass only. Also, combline functions
to eliminate usage of intermediate buffer. This gives decoder a 3%
performance gain on my test clips.
Change-Id: I13de49638884d1a57d0855c63aea719316d08c1b
This patch removes the secondary MV clamping from the MV decoder. This
behavior was consistent with limits placed on non-split MVs by the
reference encoder, but was inconsistent with the MVs generated in the
split case.
The purpose of this secondary clamping was only to prevent crashes on
invalid data. It was not intended to be a behaviour an encoder could or
should rely on. Instead of doing additional clamping in a way that
changes the entropy context, the secondary clamp is removed and the
border handling is made implmentation specific. With respect to the
spec, the border is treated as essentially infinite, limited only by
the clamping performed on the near/nearest reference and the maximum
encodable magnitude of the residual MV.
This does not affect any currently produced streams.
Change-Id: I68d35a2fbb51570d6569eab4ad233961405230a3
This patch adds support for building shared libraries when configured
with the --enable-shared switch.
Building DLLs would require more invasive changes to the sample
utilities than I want to make in this patch, since on Windows you can't
use the address of an imported symbol in a static initializer. The best
way to work around this is proably to build the codec interface mapping
table with an init() function, but dll support is of questionable value
anyway, since most windows users will probably use a media framework
lib like webmdshow, which links this library in staticly.
Change-Id: Iafb48900549b0c6b67f4a05d3b790b2643d026f4
This patch creates some basic infrastructure for doing bitstream-
incompatible changes to the VP8 encoder. The key parts are:
- --enable-experimental configure switch, to enable support for this
incompatible bitstream. This switch is required to be set to enable
any "experiments"
- A list for "experiments" which translate into --enable-<experiment>
options and CONFIG_<experiment> macros.
- The high bit of the "Version" field is used to indicate that the
bitstream was produced by an experimental encoder. The decoder will
fail to decode an experimental bitstream without
--enable-experimental.
- A new "vp8x" encoder interface is created to set the experimental
bit.
- The vp8x encoder interface is made the default for ivfenc in
experimental mode.
Change-Id: Idbdd5eae4cec5becf75bb4770837dcd256b2abef
Tests on x86 showed this function costed 2.7% of total decoding time
because of all the memory reads/writes. After modification, it only
costs about 0.7% of decoding time, which gives a 2% gain.
Change-Id: I5003ee30b6dc6dea0bfa42a6ad7e7c22fcc7b215
This is to accommodate output packets for both compressed
data and psnr stats. For each frame, there are at least
one packet for compressed data and one for psnr stats. For
a max lag of 25, 64 is large enough to cover all lagged
frames at the end of encoding.
Change-Id: If20787fbc86f96e1aa16a3ccf2adc93e6c1e3d5f
This renames the vpx_codec/ directory to vpx/, to allow applications
to more consistently reference these includes with the vpx/ prefix.
This allows the includes to be installed in /usr/local/include/vpx
rather than polluting the system includes directory with an
excessive number of includes.
Change-Id: I7b0652a20543d93f38f421c60b0bbccde4d61b4f
Avoid an potential name clashes and match other external types.
s/IMG_FMT/VPX_$&/g
s/img_fmt/vpx_$&/g
Change-Id: Ia7ad5bbb6424416b37e71e5f5eb1eca31c3c707f
This doesn't play well with autotools, and the preprocessor magic is
confusing and unhelpful in the vp8-only context.
Change-Id: I2fcb57e6eb7876ecb58509da608dc21f26077ff1
Visual c++ compiler uses xmm registers for floating point
operations for 64 bit architecture, therefore its calling
convention requires the preservation of xmm6-xmm15 in any
function that have used these registers. However, the sse2
functions, that were originally written for 32 bit windows,
may have used xmm6 and xmm7 without preserving the content.
In this particular case, the compiler used xmm6 to save
the variable "two_pass_min_rate", the value of the variable
is mucked up by our sse2 optimized loop filter functions,
hence the results of release/debug mismatching.
