Add code to monitor over and under spend and
apply limited correction to the data rate of subsequent
frames. To prevent the problem of starvation or overspend
on individual frames (especially near the end of a clip) the
maximum adjustment on a single frame is limited to a %
of its un-modified allocation.
Change-Id: I6e1ca035ab8afb0c98eac4392115d0752d9cbd7f
Turns off the DISABLE_RC_LONG_TERM_MEM macro and makes other changes
in the way the bits are updated, to make 2-pass rate control track
target bitrates closer.
Change-Id: I5f3be4b11c2908e6a9a9a1dd4fcf4e65531c44d8
Removes certain cases of feedback of active_worst_quality,
and removes it from the RATE_CONTROL structure. Now active
worst quality is expected to be computed locally in the
q picking function during the encode.
Making temporal filter strength depend on avg_frame_qindex
rather than on active_worst_quality actually improves
performance esp. for yt.
derf: +0.038%
yt: +0.359%
Change-Id: I1fe5a343034b55af9322289165321f00ac0827b1
Inlcudes a number cleanups:
1. Moves the one-pass pre-encode parameter setting functions
to vp9_ratectrl.c
2. Deprecates per_frame_bandwidth in RATE_CONTROL structure
3. Removes target_bandwidth in cpi structure since it is not used.
4. Various renaming of functions
There is no bit-stream change in 2-pass, one-pass cbr and one-pass
vbr modes.
Change-Id: Ifd9916bf4d485b7d04c5f52044ffe6703254ccbd
Some cleanups on frames_to_key, frames_since_key.
Also removes the unused fixed_q parameters in vp9.
Change-Id: If8743a32c71de30a8d17136477b53d607a7acda8
Various cleanups and refactoring.
Removes feedback of active worst qaulity and uses last_q
instead to make the interface cleaner. Active worst quality
is now decided only once for a frame being coded in the
beginning based on last_q and other stats. Also, adds other
cleaups on last_q to store also the last_q for altref frames,
and reduces the altref interval a little.
The output does change a little.
derfraw300: +0.224% (global psnr)
stdhdraw250: +0.442% (global psnr)
Change-Id: Ie634cdc032697044c472dd0fe79c109b3e7f9767
Includes various cleanups.
Streamlines the interfaces so that all rate control state
updates happen in the vp9_rc_postencode_update() function.
This will hopefully make it easier to support multiple
rate control schemes.
Removes some unnecessary code, which in rare cases can casue
a difference in the constrained quality mode output, but
other than that there is no bitstream change yet.
Change-Id: I3198cc37249932feea1e3691c0b2650e7b0c22fc
Moves all rate control variables to a separate structure,
removes some currently unused variables,
moves some rate control functions to vp9_ratectrl.c,
and splits the encode_frame_to_data_rate function.
Change-Id: I4ed54c24764b3b6de2dd676484f01473724ab52b
Some minor refactoring code relating to estimates of
bits per MB at a given Q and estimating the allowed Q range.
Most of the changes here were included in a previous commit.
This commit seeks to separate out the refactoring from more
the material changes.
Two #define control flags have been added for experimentation.
ONE_SHOT_Q_ESTIMATE force the two pass encoder to
use its initial Q range estimate for the whole clip even if this results
in a miss on the target data rate. In effect this tightens the Q range
seen at the expense of rate control accuracy.
DISABLE_RC_LONG_TERM_MEM is a related flag that disables the
long term memory in the rate control. Local adjustments are still
made to try and better hit the rate target on a per frame basis but
the impact of rate control misses is not propagated to the remainder
of the clip. This means that for example an overshoot early on will not
cause frames later in the clip to be starved of bits. Again the result
of this relaxation amy be less rate control accuracy especially on short
clips.
The flags are disabled by default for now.
Change-Id: I7482f980146d8ea033b5d50cc689f772e4bd119e
Removing redundant 'extern' keywords and parentheses, fixing indentation,
making variable names lower case, using short expressions x *= c
instead of x = x * c, minor code simplifications.
Change-Id: If6a25fcf306d1db26e90d27e3c24a32735c607de
For coefficients, use int16_t (instead of short); for pixel values in
16-bit intermediates, use uint16_t (instead of unsigned short); for all
others, use uint8_t (instead of unsigned char).
Change-Id: I3619cd9abf106c3742eccc2e2f5e89a62774f7da
Support for gyp which doesn't support multiple objects in the same
static library having the same basename.
Change-Id: Ib947eefbaf68f8b177a796d23f875ccdfa6bc9dc
