Block size passed into denoiser filter is always >= BLOCK_8X8 (in
vp9_pick_inter_mode), it is not necessary to check smaller block
size. Passed the bitexact test on clips with different resolutions and
noise levels.
Change-Id: I19fa3195d18c27d9e5de60dc11cff1522ef3714e
In VP9 internal denoiser, motion magnitude is computed from
best_sse_mv, which should be set to 0 at the begining. This bug may
cause visual aritifact in denoiser. Also, delete two improper comments.
Change-Id: I8710d2acba23320bc85cf72af17d65245c19438b
Need to check that sse for non-zero mv has been set for the current block
(i.e., check that nonzero-mv is tested as a mode, so newmv_sse != UINT_MAX)
before forcing to not use zero-mv for denoising.
Also increase some thresholds (sse and sse_diff) for high noise case,
and use shift operaton instead of multiplication on a threshold computation.
Change-Id: Iae7339475d57240316b7fa8b887c4ee3c0d0dbec
Resolved two TODO items.
Force a minimum value of 1.0 for frame duration as per section duration.
Column inactive zone is currently set to 0 as most of the serious issues
relating to inactive regions relate to letter boxing.
Change-Id: Ifbab3acf2c089d7305620a7ff7ed7c3536cc9235
In Aq mode 1 the segment and AQ delta for each block is based
on spatial variance. There may be a net imbalance between blocks
that have lower Q than the baseline value and those that have higher Q.
This patch monitors that imbalance and extends the allowed baseline
Q range for the frame to accommodate adjustment of that baseline value
to compensate.
Change-Id: Iae8a48c7c01fe2af94a141e149d03acf467237ca
So it can be used even with aq-mode=3 not enabled.
Also cleans up some code in the places where its used.
No change in behavior.
Change-Id: Ib6b265308dbd483f691200da9a0be4da4b380dbc
For 1 pass vbr mode.
Increase the gf interval for case where average Q is close to
max and high overshoot is detected.
Small increase in overall avg_psnr/sssim metrics (~0.2/0.1%) for ytlive,
but improves the low-end (low bitrate) for several clips (less overshoot).
Change-Id: Ifba40f25b4861b2e0d9832c82d5359a6a3dce9f2
More even spacing near key frame and avoid gf on scene cut
if its close to key frame.
Small increase in metrics for ytlive set (which uses key-period=150).
(~0.2% gain)
Change only affects 1 pass vbr mode.
Change-Id: If1e5a59baf1e0befbaf998522fbc47d94ac5b5df
Change only affects 1 pass vbr.
Use a q value somewhat larger (~6%) than avg_frame_qindex[INTER]
as basis for active_best_quality for inter-frames.
And use the minium of this (avg_frame_qindex) and the active_worst_quality.
This reduces some overshoot in ytlive clips.
Overall small but positive average increase in metrics (up on average ~0.2%).
Change-Id: Icdbaae7872d5675fd38a13c0ec6ce0e2e3b919ce
Change recursive weight for average_source_sad and
put some constraint on spacing between detected scene-cuts.
Change only affects 1 pass real-time mode.
Change-Id: I1917e748d845e244812d11aec2a9d755372ec182
Correct the setting of Q basis of GF/ARF in 1 pass vbr.
Existing logic would switch to using avg_QP of key frame if
avg_QP of inter is less than active worst (even if key frame is
not last frame).
Instead fix the logic (as per the comment) to use the lower of
active_worst_quality and avg_Q for inter as basis for GF/ARF
active_best_quality (unless last frame was key frame).
Increase in metrics: AvgPSNR/SSIM up by ~0.7/0.3 on ytlive set.
Change-Id: I9a628378ec6684bfda9457ebfc2384ef6d8579f7
Adjustment to stop excessive prediction decay triggered by blocks
or frames with extremely low spatial complexity which rendered the
comparison of intra and inter coded errors meaningless.
This was causing much shorter than expected groups on some 4k
test content.
Change-Id: I3f2c64200ef6dcef4721fc9f2ec09e480056ffc2
Uses a metric on fraction of smooth blocks derived from first pass
stats in a frame to adjust down the cq_level modestly in the cq mode.
The current implementation does not add much complexity, and is
fairly light in the adaptation.
Change-Id: Ic484e810d5bd51b7bb6b8945f378c7c3d9d27053
Adjust the motion decay component to account for image size.
This has very little impact for smaller image sizes.
Average bdrate results for our HD test sets:-
Hdres set: opsnr +0,92%, Fast SSIM +1.6%
Netflix hd set: opsnr + 1.5%, Fast SSIM +3.1%
There are a couple of notable -ve clips such as cyclist and sunflower
which seem to be better with a shorter interval but also a few very big
wins such as Jets >12% psnr 22% Fast SSIM and from the Netflix
Netflix set PierSeaside 9.7% psnr and 18.2% Fast SSIM.
Change-Id: Ie43aaedaa74331ed83d624a13548094ac64fed9e
Change only affects 1 pass vbr mode, speed >=5.
Increase min_thresh, decrease boost, and set a min/max
value for gf_interval.
Change-Id: I9c1e1a1ab0c5780064eb62714ee39a72ea4d2107
Trap the case where we end up with a very short arf group just before
a key frame. Such a group often has poor quality and may cause pulsing.
For example if the KF is 17 frames away we are better doing two mid-size
groups of 9 and 8 than a group of 15 followed by a group of 2.
This becomes more and more important when coding with a short forced
kf interval though it may not impact our standard tests much.
Change-Id: I29d83d6637b203eac69be320dd35a7401a4678c1
Avoid copy-block when denoising is at LowLow level (i.e., no denoising is done).
Instead, don't enter denoiser at all, and when level goes back up over kLowLow
do a reset in denoiser.
Change-Id: I0544adf58f4dd51ecc4a4607fcb0353bfbbb7a59
This make it more likely clean/low-noise content will
be set as LowLow, and hence no denoising will be done.
Also set early exit on denoising for small blocks.
Change-Id: I4a72bba3e6c5e2d523d304c39deacc9c39bf216c
