Coding and costing of mv reference signal.
Issues in updating MV ref with COMPANDED_MVREF_THRESH
to be resolved. Ideally the MV precision should be defined based
on absolute MV magnitude not as now the MV ref magnitude.
Update to mv counts moved into bitstream.c because otherwise
if the motion reference is changed at the last minute the encoder
and decoder get out of step in terms of the counts used to update
entropy probs.
Code working on a few test clips but no results yet re benefit vs
signaling cost and no tuning of red loop to test lower cost alternatives
based on the available reference values.
Patch 3. Added check to make sure we don't pick a reference
that would give rise to an uncodeable / out of range residual.
Patch 6-7: Attempt to rebase. OK to submit but best to leave flag off for now.
Patch 9. Remove print no longer needed.
Change-Id: I1938c2ffe41afe6d3cf6ccc0cb2c5d404809a712
This commit adds a pick_sb_mode() function which selects the best 32x32
superblock coding mode. Then it selects the best per-MB modes, compares
the two and encodes that in the bitstream.
The bitstream coding is rather simplistic right now. At the SB level,
we code a bit to indicate whether this block uses SB-coding (32x32
prediction) or MB-coding (anything else), and then we follow with the
actual modes. This could and should be modified in the future, but is
omitted from this commit because it will likely involve reorganizing
much more code rather than just adding SB coding, so it's better to let
that be judged on its own merits.
Gains on derf: about even, YT/HD: +0.75%, STD/HD: +1.5%.
Change-Id: Iae313a7cbd8f75b3c66d04a68b991cb096eaaba6
Incorporates mv_ref, mbsplit and second_mv into the adaptive
entropy framework. The mv_ref framework has been modified from
before.
Adds some clean-ups and fixes.
Results with the adaptive entropy experiment are currently up by
+1.93% on derf; +2.33% std-hd and +1.87% yt-hd.
Fixed a nasty intermittent bug.
Change-Id: I4b1ac9f9483b48432597595195bfec05f31d1e39
This is the first patch to add superblock (32x32) coding
order capabilities. It does not yet do any mode selection
at the SB level, that will follow in a further patch.
This patch encodes rows of SBs rather than
MBs, each SB contains 2x2 MBs.
Two intra prediction modes have been disabled since they
require reconstructed data for the above-right MB which
may not have been encoded yet (e.g. for the bottom right
MB in each SB).
Results on the one test clip I have tried (720p GIPS clip)
suggest that it is somewhere around 0.2dB worse than the
baseline version, so there may be bugs.
It has been tested with no experiments enabled and with
the following 3 experiments enabled:
--enable-enhanced_interp
--enable-high_precision_mv
--enable-sixteenth_subpel_uv
in each case the decode buffer matches the recon buffer
(using "cmp" to compare the dumped/decoded frames).
Note: Testing these experiments individually created
errors.
Some problems were found with other experiments but it
is unclear what state these experiments are in:
--enable-comp_intra_pred
--enable-newentropy
--enable-uvintra
This code has not been extensively tested yet, so there
is every likelihood that further bugs remain. I also
intend to do some code cleanup & refactoring in tandem
with the next patch that adds the 32x32 modes.
Change-Id: I1eba7f740a70b3510df58db53464535ef881b4d9
This patch introduces the concept of dual inter16x16 prediction. A
16x16 inter-predicted macroblock can use 2 references instead of 1,
where both references use the same mvmode (new, near/est, zero). In the
case of newmv, this means that two MVs are coded instead of one. The
frame can be encoded in 3 ways: all MBs single-prediction, all MBs dual
prediction, or per-MB single/dual prediction selection ("hybrid"), in
which case a single bit is coded per-MB to indicate whether the MB uses
single or dual inter prediction.
In the future, we can (maybe?) get further gains by mixing this with
Adrian's 32x32 work, per-segment dual prediction settings, or adding
support for dual splitmv/8x8mv inter prediction.
Gain (on derf-set, CQ mode) is ~2.8% (SSIM) or ~3.6% (glb PSNR). Most
gain is at medium/high bitrates, but there's minor gains at low bitrates
also. Output was confirmed to match between encoder and decoder.
Note for optimization people: this patch introduces a 2nd version of
16x16/8x8 sixtap/bilin functions, which does an avg instead of a
store. They may want to look and make sure this is implemented to
their satisfaction so we can optimize it best in the future.
Change-ID: I59dc84b07cbb3ccf073ac0f756d03d294cb19281
One of the problems arising when tweaking or adjusting the quantizer
tables is that there are a lot of look up tables that depend on the QINDEX.
Any adjustment to the link between QINDEX and real quantizer therefore tends
to break aspects of for example the rate control.
In this check in I have replaced several of the look up tables with functions that
approximate the same results as the old Q luts but use a formulaic approach
based on real Q values rather than QIndex. This should hopefully make it easier
to experiment with changes to the Q tables without always having to go through
and hand optimize a set of look up tables. Once things stabilize we may choose
to re-instate luts for the sake of performance.
Patch 2:
Addressed Ronald's comments.
vp8_init_me_luts() Added so luts only initialized once.
Change-Id: Ic80db2212d2fd01e08e8cb5c7dca1fda1102be57
This change is analogous to I0b67dae1f8a74902378da7bdf565e39ab832dda7,
which made the move for the non-RD path.
Change-Id: If63fc1b0cd1eb7f932e710f83ff24d91454f8ed1
The compiler produces better assembly when using int_mv
for assignments. The compiler shifts and ors the two 16bit
values when assigning MV.
Change-Id: I52ce4bc2bfbfaf3f1151204b2f21e1e0654f960f
The error accumulator stats values cpi->prediction_error and
cpi->intra_error were being populated with rd values not
distortion values.
These are only "currently" used in a limited way for RT compress
key frame detection.
Change-Id: I2702ba1cab6e49ab8dc096ba75b6b34ab3573021
Changes 'The VP8 project' to 'The WebM project', for consistency
with other webmproject.org repositories.
Fixes issue #97.
Change-Id: I37c13ed5fbdb9d334ceef71c6350e9febed9bbba
When the license headers were updated, they accidentally contained
trailing whitespace, so unfortunately we have to touch all the files
again.
Change-Id: I236c05fade06589e417179c0444cb39b09e4200d
