The default maximum keyframe interval is 9999, or over five minutes
at normal video rates. When the encoder produces streams with such
a long interval seeking (with correct output) is more expensive,
and live streaming is impossible.
Of course the encoding application should set this parameter
based on its knowledge of the intended use of the stream, but
reducing the default gives better results for applications
which do not.
Change-Id: I900b15d74ce72ecc3ade4d43f758c5cf97a2098a
This patch removes the local copies of the dequantize
constants and implements John's idea as described
in "Make a local copy of the dequantized data" commit.
Change-Id: Ic6b7d681f00bf63263f71ff1e39ab2f80729e8b2
In certain hardware configuration, where mmx code is enabled and
other simd (sse2/sse3) disabled, lacking of this emms caused invalid
internal stats outputs.
Change-Id: I77c61cf6e0448d3f3b8c11781aa9e42f31d231c9
Adds a multiframe postprocessing module to enhance the quality of
certain frames that are coded at lower quality than preceding frames.
The module can be invoked from the commandline by use of the --mfqe
option, and will be most beneficial for enhancing the quality of
frames decoded using scalable patterns.
Uses the vp8_variance_var16x16 and vp8_variance_sad16x16 function
pointers to compute SAD and Variance of blocks.
Change-Id: Id73d2a6e3572d07f9f8e36bbce00a4fc5ffd8961
Except zrun_zbin_boost, 15 AC values are the same for all other
parameters. Removed unneccessary calculation.
Change-Id: I6101c0fe8080bd2b4387c3b04d7ddedbf6010409
The code had a number of constructs like (condition)?1:0,
which is redundant with C's semantics. In the cases where a boolean
operator was used in the condition, simply remove the ternary part.
Otherwise adjust the surrounding expression to remove the condition
(eg, for rounding up. See pickinter.c and rdopt.c)
Change-Id: Icb2372defa3783cf31857d90b2630d06b2c7e1be
Multithreaded encoding was breaking at low bitrates
Please review/comment. Not sure if this is the best fix.
Change-Id: I87468c765372593fd865bc82e25121ebb8ca6af2
Previously, the mode context is always udpated based on stats of current
frame, when there is no count, 50% is used for both left and right branch.
However, it is observed that with such strategy, a small count or no count
at all can skew the probability distribution significantly. This commmit
changed the mode_context update strategy to prevent small counts from
skewing the probability distributions.
Tests on derf set showed a small gain: .06% in psnr and .09% in ssim
Change-Id: Ic812e64ae5f70251c170b0717f7b7fa587055488
Make bilinearfilter_arm.c compiled only when HAVE_ARMV6, as its definitions
are v6 only. This is normally not a problem for static builds as the file
is elided at link time, but this was not being done properly for the
--enable-shared --enable-pic build.
Change-Id: Ic800a7cde751f74f22555c5b247f99f9df5e550d
This commit extends the number of Q steps to 256 from 128.
The q_trans[] array has been altered to distribute available Q index values
(using the current 64 steps available as input parameters) evenly across the
available range. This is coupled with the fact that each Q step where possible
now equates to a fixed % change in the quantizer. This may want refinement
later especially in terms of the granularity at the high quality end but is a
reasonable starting point.
Change-Id: I2aaa6874fa10ce05c958dd182947ce39f6f1eecb
High Q end extended a little.
Some clean up.
Slightly better on SSIM, Slightly worse on PSNR over derf set.
Change-Id: I3dceea8a39e11c26e1a389a40e40b86efc76d28c
