mirror of
https://github.com/zeromq/libzmq.git
synced 2024-12-14 19:13:52 +01:00
4b635c3d06
Solution: update to document new binding options and IPv6 support
117 lines
3.4 KiB
Plaintext
117 lines
3.4 KiB
Plaintext
zmq_udp(7)
|
|
==========
|
|
|
|
|
|
NAME
|
|
----
|
|
zmq_udp - 0MQ UDP multicast and unicast transport
|
|
|
|
|
|
SYNOPSIS
|
|
--------
|
|
UDP is unreliable protocol transport of data over IP networks.
|
|
UDP support both unicast and multicast communication.
|
|
|
|
|
|
DESCRIPTION
|
|
-----------
|
|
UDP transport can only be used with the 'ZMQ_RADIO' and
|
|
'ZMQ_DISH' socket types.
|
|
|
|
ADDRESSING
|
|
----------
|
|
A 0MQ endpoint is a string consisting of a 'transport'`://` followed by an
|
|
'address'. The 'transport' specifies the underlying protocol to use. The
|
|
'address' specifies the transport-specific address to connect to.
|
|
|
|
For the UDP transport, the transport is `udp`.
|
|
The meaning of the 'address' part is defined below.
|
|
|
|
Binding a socket
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
|
With 'udp' we can only bind the 'ZMQ_DISH' socket type.
|
|
When binding a socket using _zmq_bind()_ with the 'udp'
|
|
transport the 'endpoint' shall be interpreted as an 'interface' followed by a
|
|
colon and the UDP port number to use.
|
|
|
|
An 'interface' may be specified by either of the following:
|
|
|
|
* The wild-card `*`, meaning all available interfaces.
|
|
* The name of the network interface (i.e. eth0, lo, wlan0 etc...)
|
|
* The primary address assigned to the interface, in its numeric representation.
|
|
* Multicast address in its numeric representation the socket should join.
|
|
|
|
The UDP port number may be specified a numeric value, usually above
|
|
1024 on POSIX systems.
|
|
|
|
Connecting a socket
|
|
~~~~~~~~~~~~~~~~~~~
|
|
With 'udp' we can only connect the 'ZMQ_RADIO' socket type.
|
|
When connecting a socket to a peer address using _zmq_connect()_ with the 'udp'
|
|
transport, the 'endpoint' shall be interpreted as a 'peer address' followed by
|
|
a colon and the UDP port number to use.
|
|
|
|
A 'peer address' may be specified by either of the following:
|
|
|
|
* The IPv4 or IPv6 address of the peer, in its numeric representation
|
|
or using its hostname.
|
|
* Multicast address in its numeric representation.
|
|
|
|
EXAMPLES
|
|
--------
|
|
.Binding a socket
|
|
----
|
|
// Unicast - UDP port 5555 on all available interfaces
|
|
rc = zmq_bind(dish, "udp://*:5555");
|
|
assert (rc == 0);
|
|
// Unicast - UDP port 5555 on the local loop-back interface
|
|
rc = zmq_bind(dish, "udp://127.0.0.1:5555");
|
|
assert (rc == 0);
|
|
// Unicast - UDP port 5555 on interface eth1
|
|
rc = zmq_bind(dish, "udp://eth1:5555");
|
|
assert (rc == 0);
|
|
// Multicast - UDP port 5555 on a Multicast address
|
|
rc = zmq_bind(dish, "udp://239.0.0.1:5555");
|
|
assert (rc == 0);
|
|
// Same as above but joining only on interface eth0
|
|
rc = zmq_bind(dish, "udp://eth0;239.0.0.1:5555");
|
|
assert (rc == 0);
|
|
// Same as above using IPv6 multicast
|
|
rc = zmq_bind(dish, "udp://eth0;[ff02::1]:5555");
|
|
assert (rc == 0);
|
|
----
|
|
|
|
|
|
.Connecting a socket
|
|
----
|
|
// Connecting using an Unicast IP address
|
|
rc = zmq_connect(radio, "udp://192.168.1.1:5555");
|
|
assert (rc == 0);
|
|
// Connecting using a Multicast address
|
|
rc = zmq_connect(socket, "udp://239.0.0.1:5555);
|
|
assert (rc == 0);
|
|
// Connecting using a Multicast address using local interface wlan0
|
|
rc = zmq_connect(socket, "udp://wlan0;239.0.0.1:5555);
|
|
assert (rc == 0);
|
|
// Connecting to IPv6 multicast
|
|
rc = zmq_connect(socket, "udp://[ff02::1]:5555);
|
|
assert (rc == 0);
|
|
----
|
|
|
|
|
|
SEE ALSO
|
|
--------
|
|
linkzmq:zmq_connect[3]
|
|
linkzmq:zmq_setsockopt[3]
|
|
linkzmq:zmq_tcp[7]
|
|
linkzmq:zmq_ipc[7]
|
|
linkzmq:zmq_inproc[7]
|
|
linkzmq:zmq_vmci[7]
|
|
linkzmq:zmq[7]
|
|
|
|
|
|
AUTHORS
|
|
-------
|
|
This page was written by the 0MQ community. To make a change please
|
|
read the 0MQ Contribution Policy at <http://www.zeromq.org/docs:contributing>.
|