Results of IDCT can by far outreach the range of ff_cropTbl[], leading
to overreads and potentially crashes.
Found-by: Mateusz "j00ru" Jurczyk and Gynvael Coldwind
CC: libav-stable@libav.org
This only returns bits per sample when it is exactly correct. That is, the
codec contains only raw samples with no frame headers or padding. This applies
to basically all PCM codecs and a small subset of ADPCM codecs.
This splits ff_dsputil_init_mmx() into multiple functions, one for
each MMX/SSE level, somewhat simplifying the nested conditions.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Diego Biurrun <diego@biurrun.de>
In most places where it's used, it's as a pointless write-only field.
Only rv10 decoder actually reads from it, but it stores some internal
version info in it. There is no reason for it to be in a public field.
Use CODEC_CAP_DELAY and CODEC_CAP_SMALL_LAST_FRAME to properly pad and flush
the encoder at the end of encoding. This is needed in order to have all input
samples decoded.
Use CODEC_CAP_DELAY and CODEC_CAP_SMALL_LAST_FRAME to properly pad and flush
the encoder at the end of encoding. This is needed in order to have all input
samples decoded.
We need to set ms_stereo in encode_init() in order to avoid incorrectly
encoding the first frame as non-m/s while flagging it as m/s. Fixes an
uncomfortable pop in the left channel at the start of playback.
CC:libav-stable@libav.org
Currently we have an assert() that prevents the frame from being too large,
but it is more user-friendly to give an error message instead of aborting on
assert(). This condition is quite unlikely due to the minimum bit rate check
in encode_init(), but it is still worth having.
The maximum theoretical frame size is around 17000 bytes. Although in
practice it will generally be much smaller, we require a larger buffer
just to be safe.
CC: libav-stable@libav.org
ff_wma_init() allows up to 50kHz, but this generates an exponent band
size table that requires 65 bands. The code assumes 25 bands in many
places, and using sample rates higher than 48kHz will lead to buffer
overwrites.
CC:libav-stable@libav.org
This is near the theoretical limit for wma frame size and is the most that
our decoder can handle. Allowing higher bit rates will just end up padding
each frame with empty bytes.
Fixes invalid writes for avconv when using very high bit rates.
CC:libav-stable@libav.org
When reading sequentially, we are using the actual flag from the previous
frame, but when seeking we do not know what the previous window flag was, so
we need to read it from the bitstream.
Prevents warnings because the dst and src overlap (are the same) in the
memcpy() inside the function.
Found-by: Mateusz "j00ru" Jurczyk and Gynvael Coldwind
CC: libav-stable@libav.org
Prevents using the invalid mode as an index in a static array, which
would generate invalid reads.
Found-by: Mateusz "j00ru" Jurczyk and Gynvael Coldwind
CC: libav-stable@libav.org
Decodes 16-bit WMA Lossless encoded files. 24-bit is not supported yet.
Bitstream parser written by Andreas Öman with contributions from
Baptiste Coudurier and Ulion.
Includes a number of bug-fixes from Benjamin Larsson, Michael Niedermayer and
Konstantin Shishkov, shine and polish by Diego Biurrun.
Signed-off-by: Diego Biurrun <diego@biurrun.de>
This fixes clipping if the encoder input used the full 16 bit
input range (samples with a magnitude below 16383 worked fine).
The filtered subband samples should be 15 bit maximum, while
the code earlier produced them scaled to 16 bit.
This makes the decoder output have double the magnitude
compared to before.
The spec reference samples doesn't test the QMF at all, which
was why this part slipped past initially.
Signed-off-by: Martin Storsjö <martin@martin.st>