The following out-of-memory check is broken.
*sorted_segments = av_mallocz(...);
if (!sorted_segments) { ... }
The correct NULL check should use *sorted_segments.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Derek Buitenhuis <derek.buitenhuis@gmail.com>
To use this, set sdpflags=custom_io to the sdp demuxer. During
the avformat_open_input call, the SDP is read from the AVFormatContext
AVIOContext (ctx->pb) - after the avformat_open_input call,
during the av_read_frame() calls, the same ctx->pb is used for reading
packets (and sending back RTCP RR packets).
Normally, one would use this with a read-only AVIOContext for the
SDP during the avformat_open_input call, then close that one and
replace it with a read-write one for the packets after the
avformat_open_input call has returned.
This allows using the RTP depacketizers as "pure" demuxers, without
having them tied to the libavformat network IO.
Signed-off-by: Martin Storsjö <martin@martin.st>
So far, aviocontexts are used either in pure-read or pure-write
mode - full read/write mode doesn't work well (and implementing it
is a much larger, not totally trivial change).
This patch allows using avio_read and ffio_read_partial on
read/write aviocontexts, where the read operations are passed
through directly unbuffered, while writes are buffered as usual.
This is enough to support the operations needed by packet based
data transfer like in udp/rtp, where aviocontext is the only
public API for hooking up custom IO.
Signed-off-by: Martin Storsjö <martin@martin.st>
The function find_things() in configure is confused by component
registration calls as part of multiline macros defining combined
component registration. Coalesce those macros into one line to
work around the issue.
Signed-off-by: Diego Biurrun <diego@biurrun.de>
Signed-off-by: Martin Storsjö <martin@martin.st>
Limelight is a not too uncommon CDN. The authentication scheme is
pretty similar to the adobe authentication, but is even closer to
normal http digest authentication (but not close enough to warrant
sharing code) than the adobe version.
Signed-off-by: Martin Storsjö <martin@martin.st>
This is mostly used to authenticate the client when publishing.
Tested with wowza and akamai.
Some but not all servers support resending a new connect invoke
within the same connection, so always reconnect for sending a new
connection attempt. This matches what other applications do as well.
The authentication scheme is structurally pretty similar to http
digest authentication, but uses base64 instead of hex strings.
Signed-off-by: Martin Storsjö <martin@martin.st>
Also fixes linking in various configs with only individual parts enabled
because the RTP muxer chaining code depends on the general RTP code,
which is now accounted for.
If s->filename doesn't contain any period/filename extension to strip
away, the buffer will be too small to fit both strings. This isn't
any buffer overflow since the concatenation uses av_strlcat with
the right buffer size.
Signed-off-by: Martin Storsjö <martin@martin.st>
This is built on the assumption that the first partition of each
VP8 packet is essential for decoding any later packet - if this
partition is broken/missed, the arithmetic coder gets out of sync
and decoding the bitstream in further packet ends up with total
garbage. If packets of a frame are lost, make sure the first
partition is intact (return only this part of the packet, nothing
else), otherwise stop returning data until the next keyframe is
received.
Alternatively, one would simply not return any packets at all
until the next keyframe, if packet loss is detected.
Signed-off-by: Martin Storsjö <martin@martin.st>
This makes all users of rtpenc_chain (rtsp muxer, sapenc, mov
rtp hinting) work again, broken since 8034130e0.
Signed-off-by: Martin Storsjö <martin@martin.st>
The FLV muxer tries to update the header in write_trailer, which is
impossible if writing to a pipe or network stream. Don't write header
data if seeking to the header fails.
Signed-off-by: Martin Storsjö <martin@martin.st>
The sample in https://bugzilla.libav.org/show_bug.cgi?id=393 and
samples/F4V/H263_NM_f.mp4 both have codec_tag H263 for different
codecs. H263 is apparently used by Flash Media Server for Sorensen
Spark videos.
Patch based on commit 5442083b1c by
Carl Eugen Hoyos. Fixes bug 393.
This makes it easier for receivers to decide what to do if data
is lost.
Refactor calculating the max payload size, to avoid hardcoding the
header size in too many places, reducing the number of lines that
have to be touched if the header is adjusted further.
Signed-off-by: Martin Storsjö <martin@martin.st>
Avoids trying to read a packet with 0 or negative size.
Avoids a potential infinite loop due to seeking backwards.
Partially based on a patch by Michael Niedermayer.
