The base_seq variable is set to first_seq - 1 (in
rtp_init_sequence), so no + 1 is needed here.
This avoids reporting 1 lost packet from the start.
Signed-off-by: Martin Storsjö <martin@martin.st>
The question can be answered: No, we do not know the initial sequence
number from the SDP. In certain cases, it can be known from the
RTP-Info response header in RTSP though. (In that case, we use it as
timestamp origin, but not for rtp receiver statistics.)
Signed-off-by: Martin Storsjö <martin@martin.st>
This is required by RFC 3550 (section 6.5):
The list of items in each chunk MUST be terminated by one or more
null octets, the first of which is interpreted as an item type of
zero to denote the end of the list.
This was implicitly added as padding before, unless the host name
length matched up so no padding was added.
This makes wireshark parse the packets properly if other RTCP items
are appended to the same packet.
Signed-off-by: Martin Storsjö <martin@martin.st>
This sends NACK for missed packets and PLI (picture loss indication)
if a depacketizer indicates that it needs a new keyframe, according
to RFC 4585.
This is only enabled if the SDP indicated that feedback is supported
(via the AVPF or SAVPF profile names).
The feedback packets are throttled to a certain maximum interval
(currently 250 ms) to make sure the feedback packets don't eat up
too much bandwidth (which might be counterproductive). The RFC
specifies a more elaborate feedback packet scheduling.
The feedback packets are currently sent independently from normal
RTCP RR packets, which is not totally spec compliant, but works
fine in the environments I've tested it in. (RFC 5506 allows this,
but requires a SDP attribute for enabling it.)
Signed-off-by: Martin Storsjö <martin@martin.st>
To use this, set sdpflags=custom_io to the sdp demuxer. During
the avformat_open_input call, the SDP is read from the AVFormatContext
AVIOContext (ctx->pb) - after the avformat_open_input call,
during the av_read_frame() calls, the same ctx->pb is used for reading
packets (and sending back RTCP RR packets).
Normally, one would use this with a read-only AVIOContext for the
SDP during the avformat_open_input call, then close that one and
replace it with a read-write one for the packets after the
avformat_open_input call has returned.
This allows using the RTP depacketizers as "pure" demuxers, without
having them tied to the libavformat network IO.
Signed-off-by: Martin Storsjö <martin@martin.st>
This comment was added in e309128f, in 2002, and has been brought
along since then more or less unmodified.
The first point of the todo was implemented in dbf30963 in 2006,
the second one is not relevant to rtpdec.c (brought along from
rtp.c in 8eb793c4 in 2008) but would be more relevant to the
rtp muxer, although it isn't a good idea anyway.
Signed-off-by: Martin Storsjö <martin@martin.st>
Mainly clean up the RTP statistics code, plus a few other obviously
misindentend lines.
Remove some useless comments, de-doxygenize some comments,
add spacing around operators and fix a typo.
Signed-off-by: Martin Storsjö <martin@martin.st>
unistd.h used to be required for gethostname. On windows, gethostname
is provided by winsock2.h. Now network.h includes both unistd.h and
winsock2.h if they exist.
Signed-off-by: Martin Storsjö <martin@martin.st>
This avoids exposing a dummy AVStream which won't get any data
and which will make avformat_find_stream_info wait for info about
this stream.
Signed-off-by: Martin Storsjö <martin@martin.st>
This is different from the "modern" RTP payload formats for H263
as defined by RFC 4629, 2429 and 3555. According to the newer RFCs,
this old one is to be considered deprecated and only be used for
interoperating with legacy systems.
Signed-off-by: Martin Storsjö <martin@martin.st>
The s->ssrc field is the sender's SSRC, we use ssrc + 1 to get
a collision free "unique" SSRC for ourselves in the RR part.
The SDES block in the RTCP packet should describe ourselves,
not the sender.
This was fixed for the RR part in 952139a322, but wasn't
fixed for the SDES part until now.
This could cause some Axis cameras to send RTCP BYE packets
to us due to the SSRC collision.
Signed-off-by: Martin Storsjö <martin@martin.st>
This requires using a separate init function, since there
isn't necessarily any fmtp lines for this codec, so
parse_sdp_a_line won't be called. Incorporating it with the
alloc function wouldn't do either, since it is called before
the full rtpmap line is parsed (where the sample rate is
extracted).
Signed-off-by: Martin Storsjö <martin@martin.st>
RTCP timestamps are only necessary to synchronize time between
multiple streams. For a single stream, the RTP packet timestamp
provides more reliable timing. As a result, single-stream RTP
sessions should now have accurate and monotonic PTS.
Signed-off-by: Martin Storsjö <martin@martin.st>
All current usages of it are incompatible with localization.
For example strcasecmp("i", "I") != 0 is possible, but would
break many of the places where it is used.
Instead use our own implementations that always treat the data
as ASCII.
Signed-off-by: Martin Storsjö <martin@martin.st>
This allows skipping past unsupported RTCP packet types, as
RFC 3550 section 6.1 mandates.
Currently this only has any practical effect if a sender puts
an unrecognized type before RTCP_BYE in a compounded packet, or
(incorrectly) does not put RTCP_SR first.
Signed-off-by: Martin Storsjö <martin@martin.st>
Most of these variables are only used in av_dlog statements, some
are required but not used by other macros.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Adding _POSIX_C_SOURCE to CPPFLAGS globally produces all sorts of problems
since it causes certain system functions to be hidden on some (BSD) systems.
The solution is to only add the flag on systems that really require it, i.e.
glibc-based ones.
This change makes BSD systems compile out-of-the-box without the need for
adding specific flags manually. It also allows dropping a number of flags
set manually on a file-per-file basis, but were only present to work around
breakage introduced by the presence of _POSIX_C_SOURCE.
Also add _XOPEN_SOURCE to CPPFLAGS for glibc systems. We use XSI extensions
in several places already, so it is preferable to define it globally instead
of littering source files with individual #defines only needed for glibc.
It doesn't look fit to be a part of the public API.
Adding a temporary hack to ffserver to be able to use it, should be
cleaned up when somebody is up for it.
In the name of consistency:
put_byte -> avio_w8
put_<type> -> avio_w<type>
put_buffer -> avio_write
put_nbyte will be made private
put_tag will be merged with avio_put_str
Signed-off-by: Ronald S. Bultje <rsbultje@gmail.com>
