Recent ICC versions that define GCC as >= 4.5 (like ICC 13) apparently can't
optimize the generic C versions of av_bswap*() on their own.
Reviewed-by: Michael Niedermayer <michaelni@gmx.at>
Signed-off-by: James Almer <jamrial@gmail.com>
Improves the accuracy of measurements, especially in short sections.
To quote the Intel 64 and IA-32 Architectures Software Developer's Manual:
"The RDTSC instruction is not a serializing instruction. It does not necessarily
wait until all previous instructions have been executed before reading the counter.
Similarly, subsequent instructions may begin execution before the read operation
is performed. If software requires RDTSC to be executed only after all previous
instructions have completed locally, it can either use RDTSCP (if the processor
supports that instruction) or execute the sequence LFENCE;RDTSC."
SSE2 is a requirement for lfence so only use it on SSE2-capable systems.
Prefer lfence;rdtsc over rdtscp since rdtscp is supported on fewer systems.
Signed-off-by: Luca Barbato <lu_zero@gentoo.org>
Silences warning(s) like:
libavcodec/x86/fft.asm:93: warning: section flags ignored on
section redeclaration
The cause of this warning is that because `struc` and `endstruc`
attempts to revert to the previous section state [1].
The section state is stored in the macro __SECT__, defined by
x86inc.asm to be `.note.GNU-stack ...`, through the `SECTION`
directive [2].
Thus, the `.note.GNU-stack` section is defined twice
(once in x86inc.asm, once during `endstruc`), causing the warning.
That is the first part of the commit: using the primitive `[section]` format
for .note.GNU-stack etc., which does not update `__SECT__` [2].
That fixes only half of the problem. Even without any `SECTION` directives,
`__SECT__` is predefined as `.text`, which conflicting with the later
`SECTION_TEXT` (which expands to `.text align=16`).
[1]: http://www.nasm.us/doc/nasmdoc6.html#section-6.4
[2]: http://www.nasm.us/doc/nasmdoc6.html#section-6.3
Signed-off-by: Luca Barbato <lu_zero@gentoo.org>
This commit silences warning(s) like:
libavcodec/x86/fft.asm:93: warning: section flags ignored on section
redeclaration
The cause of this warning is that because `struc` and `endstruc` attempts to
revert to the previous section state [1]. The section state is stored in the
macro __SECT__, defined by x86inc.asm to be `.note.GNU-stack ...`, through the
`SECTION` directive [2]. Thus, the `.note.GNU-stack` section is defined twice
(once in x86inc.asm, once during `endstruc`), causing the warning.
That is the first part of the commit: using the primitive `[section]` format
for .note.GNU-stack etc., which does not update `__SECT__` [2].
That fixes only half of the problem. Even without any `SECTION` directives,
`__SECT__` is predefined as `.text`, which conflicting with the later
`SECTION_TEXT` (which expands to `.text align=16`).
[1]: http://www.nasm.us/doc/nasmdoc6.html#section-6.4
[2]: http://www.nasm.us/doc/nasmdoc6.html#section-6.3
Signed-off-by: Michael Niedermayer <michaelni@gmx.at>
SSE2 instructions that are XMM-implementations of pre-existing MMX/MMX2
instructions did not issue warnings when used in SSE functions. Handle
it by also checking the register type when such instructions are used.
Signed-off-by: Michael Niedermayer <michaelni@gmx.at>
This mimicks what is done for the other instruction sets.
Tested-by: James Almer <jamrial@gmail.com>
Tested-by: Mickaël Raulet <mraulet@gmail.com>
Signed-off-by: Michael Niedermayer <michaelni@gmx.at>
~560 → ~500 decicycles
This is following the comments from Michael in
https://ffmpeg.org/pipermail/ffmpeg-devel/2014-August/160599.html
Using 2 registers for accumulator didn't help. On the other hand,
some re-ordering between the movs and psadbw allowed going ~538 to ~500.
Up to four instructions less depending on function and instruction set.
Signed-off-by: James Almer <jamrial@gmail.com>
Signed-off-by: Michael Niedermayer <michaelni@gmx.at>
Only 8-bit and 10-bit idct_dc() functions are included (adding others should be trivial).
Benchmarks on an Intel Core i5-4200U:
idct8x8_dc
SSE2 MMXEXT C
cycles 22 26 57
idct16x16_dc
AVX2 SSE2 C
cycles 27 32 249
idct32x32_dc
AVX2 SSE2 C
cycles 62 126 1375
Signed-off-by: James Almer <jamrial@gmail.com>
Reviewed-by: Mickaël Raulet <mraulet@gmail.com>
Signed-off-by: Michael Niedermayer <michaelni@gmx.at>
Those macros take a byte number as shift argument, as this argument
differs between MMX and SSE2 instructions.
Signed-off-by: Michael Niedermayer <michaelni@gmx.at>
It was lost during the port.
Should fix fate on 3dnowext machines.
Signed-off-by: James Almer <jamrial@gmail.com>
Signed-off-by: Michael Niedermayer <michaelni@gmx.at>
Use the xm# and ym# aliases as they remain in sync with m# after a SWAP.
No actual changes to the assembly.
Signed-off-by: James Almer <jamrial@gmail.com>
Signed-off-by: Michael Niedermayer <michaelni@gmx.at>
Also port relevant AVX2/XOP optimizations from x264 with permission
to relicense to LGPL from the corresponding authors
Signed-off-by: James Almer <jamrial@gmail.com>
Reviewed-by: "Ronald S. Bultje" <rsbultje@gmail.com>
Signed-off-by: Michael Niedermayer <michaelni@gmx.at>
