This adds three new options to control the behavior of TCP keepalives:
- CURLOPT_TCP_KEEPALIVE: enable/disable probes
- CURLOPT_TCP_KEEPIDLE: idle time before sending first probe
- CURLOPT_TCP_KEEPINTVL: delay between successive probes
While not all operating systems support the TCP_KEEPIDLE and
TCP_KEEPINTVL knobs, the library will still allow these options to be
set by clients, silently ignoring the values.
Do not try to resolve interfaces names via DNS by recognizing interface
names in a few ways. If the interface option argument has a prefix of
"if!" then treat the argument as only an interface. Similarly, if the
interface argument is the name of an interface (even if it does not have
an IP address assigned), treat it as an interface name. Finally, if the
interface argument is prefixed by "host!" treat it as a hostname that
must be resolved by /etc/hosts or DNS.
These changes allow a client using the multi interfaces to avoid
blocking on name resolution if the interface loses its IP address or
disappears.
If the option is set to 0, the default timeout will be used - which in
modern libcurl versions equals 300 seconds (== 5 minutes).
Bug: http://curl.haxx.se/mail/lib-2011-12/0051.html
Reported by: Vladimir Grishchenko
When the new socket is created for an active connection, it is now done
using the open socket callback.
Test case 596 was modified to run fine, although it hides the fact that
the close callback is still called too many times, as it also gets
called for closing sockets that were created with accept().
Added pop3 username and password example as well as an explanation of
how path part of the URL is used under pop3.
Additionally have corrected a couple of typos.
Slight rewording of the CURLOPT_URL SMTP sub-section.
Corrected the incorrect use of hyphens on the three uses of
"zero-terminated" with "zero terminated" to match the rest of the
document.
Corrected the use of an out of place hyphen in CURLOPT_NOPROXY section.
Allow (*curl_write_callback) write callbacks to return
CURL_WRITEFUNC_OUT_OF_MEMORY to properly indicate libcurl of OOM conditions
inside the callback itself.
Using 'socks5h' as proxy protocol will make it a
CURLPROXY_SOCKS5_HOSTNAME proxy which is SOCKS5 and asking the proxy to
resolve host names. I found no "standard" protocol name for this.
The read callback must return the exact requested amount of data when it
is used for doing TFTP uploads. This is due to how it deals with data
internally. This could/should be fixed but for now we document the
existing behavior.
Reported by: Colin Blair
Bug: http://curl.haxx.se/mail/lib-2011-03/0319.html
When NSS-powered libcurl connected to a SSL server with
CURLOPT_SSL_VERIFYPEER equal to zero, NSS remembered that the peer
certificate was accepted by libcurl and did not ask the second time when
connecting to the same server with CURLOPT_SSL_VERIFYPEER equal to one.
This patch turns off the SSL session cache for the particular SSL socket
if peer verification is disabled. In order to avoid any performance
impact, the peer verification is completely skipped in that case, which
makes it even faster than before.
Bug: https://bugzilla.redhat.com/678580
... and update the curl.1 and curl_easy_setopt.3 man pages such that
they do not suggest to use an OpenSSL utility if curl is not built
against OpenSSL.
Bug: https://bugzilla.redhat.com/669702
This is a meta symbol. OR this value together with a single specific
auth value to force libcurl to probe for un-restricted auth and if not,
only that single auth algorithm is acceptable.
For example you can use CURLAUTH_DIGEST|CURLAUTH_ONLY to make libcurl
first probe for what method to use, but yet only consider Digest to be
acceptable.
Using _only_ CURLAUTH_DIGEST without the CURLAUTH_ONLY field, will make
libcurl explicitly use Digest right away and not do any probing.
The numerical value passed to CURLOPT_RESUME_FROM for FTP uploads is
interpreted and used as position where to resume the _reading_ of the
local file and it will "blindly" append that data on the remote
file. This was certainly not clear in the docs previously.
Reported by: catalin
Bug: http://curl.haxx.se/bug/view.cgi?id=3048174
In some places where the name 'stream' has been used for naming a
function argument that is in fact settable with a setopt() option we now
call that argument 'userdata' to make it more obvious that it is in fact
possible to set by the application.
Suggested by: Jeff Pohlmeyer
properly in angle brackets. Recipients provided with CURLOPT_MAIL_RCPT now
get angle bracket wrapping automatically by libcurl unless the recipient
starts with an angle bracket as then the app is assumed to deal with that
properly on its own.
command is a special "hack" used by the drftpd server, but even though it is
a custom extension I've deemed it fine to add to libcurl since this server
seems to survive and people keep using it and want libcurl to support
it. The new libcurl option is named CURLOPT_FTP_USE_PRET, and it is also
usable from the curl tool with --ftp-pret. Using this option on a server
that doesn't support this command will make libcurl fail.
Chen pointed out how curl couldn't upload with resume when reading from a
pipe.
This ended up with the introduction of a new return code for the
CURLOPT_SEEKFUNCTION callback that basically says that the seek failed but
that libcurl may try to resolve the situation anyway. In our case this means
libcurl will attempt to instead read that much data from the stream instead
of seeking and that way curl can now upload with resume when data is read
from a stream!
and 1 on fatal errors. Previously it only mentioned non-zero on fatal
errors. This is a slight change in meaning, but it follows what we've done
elsewhere before and it opens up for LOTS of more useful return codes
whenever we can think of them...
(http://curl.haxx.se/docs/adv_20090303.html also known as CVE-2009-0037) in
which previous libcurl versions (by design) can be tricked to access an
arbitrary local/different file instead of a remote one when
CURLOPT_FOLLOWLOCATION is enabled. This flaw is now fixed in this release
together this the addition of two new setopt options for controlling this
new behavior:
o CURLOPT_REDIR_PROTOCOLS controls what protocols libcurl is allowed to
follow to when CURLOPT_FOLLOWLOCATION is enabled. By default, this option
excludes the FILE and SCP protocols and thus you nee to explicitly allow
them in your app if you really want that behavior.
o CURLOPT_PROTOCOLS controls what protocol(s) libcurl is allowed to fetch
using the primary URL option. This is useful if you want to allow a user or
other outsiders control what URL to pass to libcurl and yet not allow all
protocols libcurl may have been built to support.
plain FTP connections, and it will then allow MKD to fail once and retry the
CWD afterwards. This is especially useful if you're doing many simultanoes
connections against the same server and they all have this option enabled,
as then CWD may first fail but then another connection does MKD before this
connection and thus MKD fails but trying CWD works! The numbers can
(should?) now be set with the convenience enums now called
CURLFTP_CREATE_DIR and CURLFTP_CREATE_DIR_RETRY.
Tests has proven that if you're making an application that uploads a set of
files to an ftp server, you will get a noticable gain in speed if you're
using multiple connections and this option will be then be very useful.
the condition in the previous request was unmet. This is typically a time
condition set with CURLOPT_TIMECONDITION and was previously not possible to
reliably figure out. From bug report #2565128
(http://curl.haxx.se/bug/view.cgi?id=2565128)
version 1.1 instead of 1.0 like before. This change also introduces the new
proxy type for libcurl called 'CURLPROXY_HTTP_1_0' that then allows apps to
switch (back) to CONNECT 1.0 requests. The curl tool also got a --proxy1.0
option that works exactly like --proxy but sets CURLPROXY_HTTP_1_0.
I updated all test cases cases that use CONNECT and I tried to do some using
--proxy1.0 and some updated to do CONNECT 1.1 to get both versions run.
CURLOPT_SOCKS5_GSSAPI_SERVICE and CURLOPT_SOCKS5_GSSAPI_NEC to allow libcurl
to do GSS-style authentication with SOCKS5 proxies. The curl tool got the
options called --socks5-gssapi-service and --socks5-gssapi-nec to enable
these.
They basically offer the same thing the NO_PROXY environment variable only
offered previously: list a set of host names that shall not use the proxy
even if one is specified.
there are servers "out there" that relies on the client doing this broken
Digest authentication. Apache even comes with an option to work with such
broken clients.
The difference is only for URLs that contain a query-part (a '?'-letter and
text to the right of it).
libcurl now supports this quirk, and you enable it by setting the
CURLAUTH_DIGEST_IE bit in the bitmask you pass to the CURLOPT_HTTPAUTH or
CURLOPT_PROXYAUTH options. They are thus individually controlled to server
and proxy.
make CURLOPT_PROXYUSERPWD sort of deprecated. The primary motive for adding
these new options is that they have no problems with the colon separator
that the CURLOPT_PROXYUSERPWD option does.
curl_easy_setopt: CURLOPT_USERNAME and CURLOPT_PASSWORD that sort of
deprecates the good old CURLOPT_USERPWD since they allow applications to set
the user name and password independently and perhaps more importantly allow
both to contain colon(s) which CURLOPT_USERPWD doesn't fully support.
enabling this feature with CURLOPT_CERTINFO for a request using SSL (HTTPS
or FTPS), libcurl will gather lots of server certificate info and that info
can then get extracted by a client after the request has completed with
curl_easy_getinfo()'s CURLINFO_CERTINFO option. Linus Nielsen Feltzing
helped me test and smoothen out this feature.
Unfortunately, this feature currently only works with libcurl built to use
OpenSSL.
This feature was sponsored by networking4all.com - thanks!
parser to allow numerical IPv6-addresses to be specified with the scope
given, as per RFC4007 - with a percent letter that itself needs to be URL
escaped. For example, for an address of fe80::1234%1 the HTTP URL is:
"http://[fe80::1234%251]/"
non-zero with the fixed value of 1. We should strive at making options
support '1' for enabling them mentioned explicitly, as that then will allow
us for to extend them in the future without breaking older programs.
curl-library list on July 9th 2008 by Mathew Hounsell)
NOTE: the name resolve functions of various libc implementations don't re-read
name server information unless explicitly told so (by for example calling
Ires_init(3). This may cause libcurl to keep using the older server even
if DHCP has updated the server info, and this may look like a DNS cache issue
to the casual libcurl-app user.
libcurl to seek in a given input stream. This is particularly important when
doing upload resumes when there's already a huge part of the file present
remotely. Before, and still if this callback isn't used, libcurl will read
and through away the entire file up to the point to where the resuming
begins (which of course can be a slow opereration depending on file size,
I/O bandwidth and more). This new function will also be preferred to get
used instead of the CURLOPT_IOCTLFUNCTION for seeking back in a stream when
doing multi-stage HTTP auth with POST/PUT.
code to instead introduce support for a new proxy type called
CURLPROXY_SOCKS5_HOSTNAME that is used to send the host name to the proxy
instead of IP address and there's thus no longer any need for a new
curl_easy_setopt() option.
The default SOCKS5 proxy is again back to sending the IP address to the
proxy. The new curl command line option for enabling sending host name to a
SOCKS5 proxy is now --socks5-hostname.
proxy do the host name resolving and only if --socks5ip (or
CURLOPT_SOCKS5_RESOLVE_LOCAL) is used we resolve the host name locally and
pass on the IP address only to the proxy.
is an inofficial PROXY4 variant that sends the hostname to the proxy instead
of the resolved address (which is already supported by SOCKS5). --socks4a is
the curl command line option for it and CURLOPT_PROXYTYPE can now be set to
CURLPROXY_SOCKS4A as well.
the appending of the "type=" thing on FTP URLs when they are passed to a
HTTP proxy. Some proxies just don't like that appending (which is done
unconditionally in 7.17.1), and some proxies treat binary/ascii transfers
better with the appending done!
