Bob Richmond: There's an annoying situation where libcurl will
read new HTTP response data from a socket, then check if it's a
timeout if one is set. If the last packet received constitutes
the end of the response body, libcurl still treats it as a
timeout condition and reports a message like:
"Operation timed out after 3000 milliseconds with 876 out of 876
bytes received"
It should only a timeout if the timer lapsed and we DIDN'T
receive the end of the response body yet.
makes sure that when using sub-second timeouts, there's no final bad 1000ms
wait. Previously, a sub-second timeout would often make the elapsed time end
up the time rounded up to the nearest second (e.g. 1s for 200ms timeout)
sequences in uploaded data. The test server doesn't "decode" escaped dot-lines
but instead test cases must be written to take them into account. Added test
case 803 to verify dot-escaping.
the define CURL_MAX_HTTP_HEADER which is even exposed in the public header
file to allow for users to fairly easy rebuild libcurl with a modified
limit. The rationale for a fixed limit is that libcurl is realloc()ing a
buffer to be able to put a full header into it, so that it can call the
header callback with the entire header, but that also risk getting it into
trouble if a server by mistake or willingly sends a header that is more or
less without an end. The limit is set to 100K.
transfer.c for blocking. It is currently used only by SCP and SFTP protocols.
This enhancement resolves an issue with 100% CPU usage during SFTP upload,
reported by Vourhey.
strdup() that could lead to segfault if it returned NULL. I extended his
suggest patch to now have Curl_retry_request() return a regular return code
and better check that.
Fix SIGSEGV on free'd easy_conn when pipe unexpectedly breaks
Fix data corruption issue with re-connected transfers
Fix use after free if we're completed but easy_conn not NULL
With the curl memory tracking feature decoupled from the debug build feature,
CURLDEBUG and DEBUGBUILD preprocessor symbol definitions are used as follows:
CURLDEBUG used for curl debug memory tracking specific code (--enable-curldebug)
DEBUGBUILD used for debug enabled specific code (--enable-debug)
KEEP_RECV to better match the general terminology: receive and send is what we
do from the (remote) servers. We read and write from and to the local fs.
libcurl did a superfluous 1000ms wait when doing SFTP downloads!
We read data with libssh2 while doing the "DO" operation for SFTP and then
when we were about to start getting data for the actual file part, the
"TRANSFER" part, we waited for socket action (in 1000ms) before doing a
libssh2-read. But in this case libssh2 had already read and buffered the
data so we ended up always just waiting 1000ms before we get working on the
data!
the condition in the previous request was unmet. This is typically a time
condition set with CURLOPT_TIMECONDITION and was previously not possible to
reliably figure out. From bug report #2565128
(http://curl.haxx.se/bug/view.cgi?id=2565128)
now has an improved ability to do right when the multi interface (both
"regular" and multi_socket) is used for SCP and SFTP transfers. This should
result in (much) less busy-loop situations and thus less CPU usage with no
speed loss.
(http://curl.haxx.se/bug/view.cgi?id=2155496) pointing out an error case
without a proper human-readable error message. When a read callback returns
a too large value (like when trying to return a negative number) it would
trigger and the generic error message then makes the proplem slightly
different to track down. I've added an error message for this now.
fixed a CURLINFO_REDIRECT_URL memory leak and an additional wrong-doing:
Any subsequent transfer with a redirect leaks memory, eventually crashing
the process potentially.
Any subsequent transfer WITHOUT a redirect causes the most recent redirect
that DID occur on some previous transfer to still be reported.
